[AM3359 WinCE7][BSP_WINCE_ARM_A8_02_30_00]Ethernet IP101A with RMII interface-TI中文支持网

I am devloping Ethernet IP101A with RMII interface on AM335x wince7 platform. Now IP101A is detected successfully.

but can not get IP address with DHCP mode; if set static IP, then can not pin successfully the wince on PC.

I also check the interrupt in

Cpsw3g_intr.c (platform\common\src\soc\common_ti_v1\am33x\cpsw3gminiport) file, there is only have TX interrupt, there is no RX interrupt.

could you please help me check this issue? below is my uart debug message:

CCCCCCCC
Texas Instruments Windows2 CE SD X-Loader v0.0.0 for SubArctic 33X
Built Feb 27 2013 at 17:09:22
Version BSP_WINCE_ARM_A8 02.30.00.01
open ebootsd.nb0 file
BLSDCardDownload: Filename ebootsd.nb0
Init HW: controller RST
SDCARD: requested speed 1000000, actual speed 1000000
SDCARD: requested speed 25000000, actual speed 19200000
BLSDCardDownload: success open file EOTDB
read ebootsd.nb0 file

XLDRMSGDEINIT

Microsoft Windows CE Bootloader Common Library Version 1.4 Built Feb 26 2013 09:40:33
BSPGetDevicePadInfo:board ID 0
BSPGetDevicePadInfo: BoardProfile=1,BoardHasDcard=1
BSPGetDevicePadInfo:board ID 0
BSPGetDevicePadInfo: BoardProfile=1,BoardHasDcard=1
BSPGetDevicePadInfo:board ID 0
BSPGetDevicePadInfo: BoardProfile=1,BoardHasDcard=1
BSPGetDevicePadInfo:board ID 0
BSPGetDevicePadInfo: BoardProfile=1,BoardHasDcard=1
BSPGetDevicePadInfo:board ID 0
BSPGetDevicePadInfo: BoardProfile=1,BoardHasDcard=1
BSPGetDevicePadInfo:board ID 0
BSPGetDevicePadInfo: BoardProfile=1,BoardHasDcard=1
INFO:OALLogSetZones: dpCurSettings.ulZoneMask: 0x8409

Texas Instruments Windows CE EBOOT for AM33x, Built Feb 27 2013 at 17:09:15
EBOOT Version 0.0.1, BSP BSP_WINCE_ARM_A8 02.30.00.01

TI AM33X GPIOInit

TI AM33X

ecc type:2
System ready!
Preparing for download…
INFO: Predownload….
BLShowLogo+++++++++++++++++
SD ShowSDLogo~~~~~~~~~~~~~~~~~~~~~~~
SetBacklightPower_OnOff======0=======+++++
SetBacklightLevel_GPIO=======ff======+++++
Pclk …………… 300000000
BLShowLogo—————–
SetBacklightPower_OnOff======1=======+++++
Checking bootloader blocks are marked as reserved (Num = 34)

INFO: Boot configuration found. Boot config Version 3, Signature 1111705159
IsValidMBR: MBR sector = 0xa80 (valid MBR)
OpenPartition: Partition Exists=0x1 for part 0x20.

>>> Forcing cold boot (non-persistent registry and other data will be wiped) <<<
ed311800 7fb7 -> 0 18 31 ed b7 7f
ed311800 80c1 -> 0 18 31 ed c1 80
Hit space to enter configuration menu [610] 2…
Hit space to enter configuration menu [1610] 1…
OEMPreDownload: Filename nk.bin
BLSDCardDownload: Filename nk.bin
Init HW: controller RST
SDCARD: requested speed 1000000, actual speed 1000000
SDCARD: requested speed 25000000, actual speed 19200000
BLSDCardDownload: success open file N I

BL_IMAGE_TYPE_BIN

+OEMMultiBinNotify(0x8fe2a978 -> 1)
Download file information:
———————————————————–
[0]: Address=0x80002000 Length=0x044cd960 Save=0x80002000
———————————————————–
Download file type: 1
+OEMIsFlashAddr(0x80002000) g_eboot.type 1
………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………..rom_offset=0x0.
..ImageStart = 0x80002000, ImageLength = 0x44cd960, LaunchAddr = 0x8000b280

Completed file(s):
——————————————————————————-
+OEMIsFlashAddr(0x80002000) g_eboot.type 1
[0]: Address=0x80002000 Length=0x44cd960 Name="" Target=RAM
ROMHDR at Address 80002044h

Writing NK image to OS partition

ROMHDR (pTOC = 0x844cbb50) ———————
DLL First : 0x4001eef8
DLL Last : 0x4319f000
Physical First : 0x80002000
Physical Last : 0x844cf960
Num Modules : 367
RAM Start : 0x844d0000
RAM Free : 0x844e5000
RAM End : 0x8d000000
Num Copy Entries : 2
Copy Entries Offset : 0x82dd4d88
Prof Symbol Length : 0x00000000
Prof Symbol Offset : 0x00000000
Num Files : 145
Kernel Flags : 0x00000000
FileSys RAM Percent : 0x0a0a0a0a
Driver Glob Start : 0x00000000
Driver Glob Length : 0x00000000
CPU : 0x01c2
MiscFlags : 0x0002
Extensions : 0x80003020
Tracking Mem Start : 0x00000000
Tracking Mem Length : 0x00000000
————————————————

IsValidMBR: MBR sector = 0xa80 (valid MBR)
OpenPartition: Partition Exists=0x1 for part 0x20.
BP_SetDataPointer at 0x44cd960
BP_SetDataPointer at 0x0
WriteData: Start = 0x0, Length = 0x44cd960.
NK image written
Launch Windows CE image by jumping to 0x8000b280…

Windows CE Kernel for ARM (Thumb Enabled)
CPU CP15 Control Register = 0xc5387f
CPU CP15 Auxiliary Control Register = 0x42
+OALInterruptInit
-OALInterruptInit(rc = 1)
+OALTimerInit(1, 24000, 200)
BSPGetDevicePadInfo:board ID 0
BSPGetDevicePadInfo: BoardProfile=1,BoardHasDcard=1
RequestAndConfigurePadArray+
RequestAndConfigurePadArray successfully
— High Performance Frequecy is 24 MHz—
PID:00400002 TID:00410002 SetOpp to 3
PID:00400002 TID:01370006 BSPGetDevicePadInfo:board ID 0
PID:00400002 TID:01370006 BSPGetDevicePadInfo: BoardProfile=1,BoardHasDcard=1
PID:00400002 TID:01370006 RequestAndConfigurePadArray+
PID:00400002 TID:01370006 RequestAndConfigurePadArray successfully
PID:00400002 TID:01370006 ECC TYPE is BCH 8 bit
PID:00400002 TID:01370006 8Bit NAND device
PID:00400002 TID:01370006 CM3: input file [\windows\firmware.bin] is 9932 bytes long
PID:00400002 TID:01370006 CM3: firmware file read ok!
PID:00400002 TID:01370006 +SPK_Init(Drivers\Active\17, 0x00000000)
PID:00400002 TID:01370006 RequestAndConfigurePadArray+
PID:00400002 TID:01370006 RequestAndConfigurePadArray successfully
PID:00400002 TID:01370006 Vibrator: successs to request pads
PID:00400002 TID:01370006 SPK_Init: success to open GPIO driver
PID:00400002 TID:01370006 -SPK_Init(rc = -273763708)
PID:00400002 TID:01370006 LinkSpeed is not currently supported.
PID:00400002 TID:01370006 LinkDuplex is not currently supported.
PID:00400002 TID:01370006 Cpsw_read_port_setting: read subkey failed
PID:00400002 TID:01370006 Read port settings failed
PID:00400002 TID:01370006 Xgmii_sel=45
PID:00400002 TID:01370006 Xgmii_sel=45
PID:00400002 TID:01370006 Cpsw3gReadMacAddrFromFuse: ed311800 7fb7 -> 0 18 31 ed b7 7f
PID:00400002 TID:01370006 Cpsw_read_port_setting: read subkey failed
PID:00400002 TID:01370006 LinkSpeed is not currently supported.
PID:00400002 TID:01370006 LinkDuplex is not currently supported.
PID:00400002 TID:01370006 cpsw_add_static_ALE_entry: reading entry 0 failed
PID:00400002 TID:01370006 cpsw_add_static_ALE_entry: reading entry 1 failed
PID:00400002 TID:01370006 cpsw_add_static_ALE_entry: reading entry 2 failed
PID:00400002 TID:01370006 cpsw_add_static_ALE_entry: reading entry 3 failed
PID:00400002 TID:01370006 Cpsw_add_vlan_ALE_entry: entry 0 does not exist PID:00400002 TID:01370006 Cpsw_add_vlan_ALE_entry: entry 1 does not exist PID:00400002 TID:01370006 Cpsw_add_vlan_ALE_entry: entry 2 does not exist PID:00400002 TID:01370006 Cpsw_add_vlan_ALE_entry: entry 3 does not exist PID:00400002 TID:01370006 Cpsw_add_vlan_ALE_entry: entry 4 does not exist PID:00400002 TID:01370006 Cpsw_add_vlan_ALE_entry: entry 5 does not exist PID:00400002 TID:01370006 Cpsw_add_vlan_ALE_entry: entry 6 does not exist PID:00400002 TID:01370006 Cpsw_add_vlan_ALE_entry: entry 7 does not exist PID:00400002 TID:01370006 Cpsw3g_read_KITL_port failed!
PID:00400002 TID:01370006 Cpsw3g_read_Speed_Match failed!
PID:00400002 TID:01370006 Cpsw3g Configuration:
PID:00400002 TID:01370006 RxThreshInterrupt: 40
PID:00400002 TID:01370006 RxInterrupt: 41
PID:00400002 TID:01370006 TxInterrupt: 42
PID:00400002 TID:01370006 MiscInterrupt: 43
PID:00400002 TID:01370006 cpsw3g_mode: 1
PID:00400002 TID:01370006 KITL_port: 1
PID:00400002 TID:01370006 ALE_Agingtimer: 131072
PID:00400002 TID:01370006 MacAuth: 0
PID:00400002 TID:01370006 UnknownUntagEgress: 0
PID:00400002 TID:01370006 UnknownRegMcastFloodMask: 0
PID:00400002 TID:01370006 UnknownMcastFloodMask: 0
PID:00400002 TID:01370006 UnknownMemberList: 0
PID:00400002 TID:01370006 Enable_8021x: 0
PID:00400002 TID:01370006 rxVlanEncap: 0
PID:00400002 TID:01370006 sw_vlantagging: 0
PID:00400002 TID:01370006 KITL_enable: 0
PID:00400002 TID:01370006 stats_port_mask: 7
PID:00400002 TID:01370006 Cpsw3g MAC portConfiguration: port 1
PID:00400002 TID:01370006 PhyAddr: 1
PID:00400002 TID:01370006 LinkSpeed: 0
PID:00400002 TID:01370006 LinkDuplex: 0
PID:00400002 TID:01370006 portPriority: 0
PID:00400002 TID:01370006 portVID: 0
PID:00400002 TID:01370006 bcastLimit: 0
PID:00400002 TID:01370006 mcastLimit: 0
PID:00400002 TID:01370006 VIDIngressCheck: 0
PID:00400002 TID:01370006 DropUntagged: 0
PID:00400002 TID:01370006 rxMaxlen: 1518
PID:00400002 TID:01370006 passCrc: 0
PID:00400002 TID:01370006 phy addr: 1
PID:00400002 TID:01370006 Cpsw3g MAC portConfiguration: port 2
PID:00400002 TID:01370006 PhyAddr: 0
PID:00400002 TID:01370006 LinkSpeed: 0
PID:00400002 TID:01370006 LinkDuplex: 0
PID:00400002 TID:01370006 portPriority: 0
PID:00400002 TID:01370006 portVID: 0
PID:00400002 TID:01370006 bcastLimit: 250
PID:00400002 TID:01370006 mcastLimit: 250
PID:00400002 TID:01370006 VIDIngressCheck: 0
PID:00400002 TID:01370006 DropUntagged: 0
PID:00400002 TID:01370006 rxMaxlen: 1518
PID:00400002 TID:01370006 passCrc: 0
PID:00400002 TID:01370006 phy addr: 0
PID:00400002 TID:01370006 Cpsw3g MAC portConfiguration: port 0
PID:00400002 TID:01370006 portPriority: 0
PID:00400002 TID:01370006 portVID: 0
PID:00400002 TID:01370006 bcastLimit: 250
PID:00400002 TID:01370006 mcastLimit: 250
PID:00400002 TID:01370006 VIDIngressCheck: 0
PID:00400002 TID:01370006 DropUntagged: 0
PID:00400002 TID:01370006 Xgmii_sel=45
PID:00400002 TID:01370006 Xgmii_sel=45
PID:00400002 TID:01370006 Cpsw3gReadMacAddrFromFuse: ed311800 7fb7 -> 0 18 31 ed b7 7f
PID:00400002 TID:01370006 OALIntrEnableIrqs(CPSW Irq 40)
PID:00400002 TID:01370006 OALIntrDoneIrqs(CPSW Irq 40)
PID:00400002 TID:01370006 ** cpsw3g_miniport 1: The sysintr chosen for 40 by NDIS is 23
PID:00400002 TID:01370006 OALIntrEnableIrqs(CPSW Irq 41)
PID:00400002 TID:01370006 OALIntrDoneIrqs(CPSW Irq 41)
PID:00400002 TID:01370006 ** cpsw3g_miniport 1: The sysintr chosen for 41 by NDIS is 24
PID:00400002 TID:01370006 OALIntrEnableIrqs(CPSW Irq 42)
PID:00400002 TID:01370006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:01370006 ** cpsw3g_miniport 1: The sysintr chosen for 42 by NDIS is 25
PID:00400002 TID:01370006 OALIntrEnableIrqs(CPSW Irq 43)
PID:00400002 TID:01370006 OALIntrDoneIrqs(CPSW Irq 43)
PID:00400002 TID:01370006 ** cpsw3g_miniport 1: The sysintr chosen for 43 by NDIS is 26
PID:00400002 TID:01370006 Cpsw3g_InitializeAdapter: mode=1, port=1, txCh=0, rxChMask=0x01, ActiveCpgmac=1
PID:00400002 TID:01370006 ++ Cpsw3g_cpgmac_setup : port 1
PID:00400002 TID:01370006 +Cpsw3g_ModStateChange
PID:00400002 TID:01370006 -Cpsw3g_ModStateChange
PID:00400002 TID:01370006 +Cpsw3g_ModStateChange
PID:00400002 TID:01370006 -Cpsw3g_ModStateChange
PID:00400002 TID:01370006 ***** Cpsw3g_Phy_Init: port 0 phy_addr:1, state=0.
PID:00400002 TID:01370006 Cpsw3g_Phy_Init: phy timer is started, timeout every:10.
PID:00400002 TID:01370006 <– Cpsw3g_InitializeAdapter.
PID:00400002 TID:02D60002 _cpsw3g_Phy_Init_state: phy_mask 2
PID:00400002 TID:02D60002 _cpsw3g_Phy_Init_state: phy_mask 2, PhyAcks2 alive:2
PID:00400002 TID:02D60002 *** PhyAcks=0x2 i=1
PID:00400002 TID:02D60002 *** PhyNum=0x1 i=1
PID:00400002 TID:02D60002 *** PhyNum=0x1 phy_addr=1
PID:00400002 TID:02D60002 PHY id : 02430C54
PID:00400002 TID:02D60002 _cpsw3g_find_phy_driver
PID:00400002 TID:02D60002 _cpsw3g_phy_softreset
PID:00400002 TID:02D60002 init
PID:00400002 TID:02D60002 config_autoneg
PID:00400002 TID:02D60002 -> ip101a_reg_dump start:
PID:00400002 TID:02D60002 IP101A Register0: 3100
PID:00400002 TID:02D60002 IP101A Register1: 7849
PID:00400002 TID:02D60002 IP101A Register2: 243
PID:00400002 TID:02D60002 IP101A Register3: c54
PID:00400002 TID:02D60002 IP101A Register4: 1e1
PID:00400002 TID:02D60002 IP101A Register5: 0
PID:00400002 TID:02D60002 IP101A Register6: 0
PID:00400002 TID:02D60002 IP101A Register16: 2
PID:00400002 TID:02D60002 IP101A Register17: f40
PID:00400002 TID:02D60002 IP101A Register18: 6000
PID:00400002 TID:02D60002 IP101A Register30: 2
PID:00400002 TID:02D60002 -> ip101a_reg_dump end!
PID:00400002 TID:01370006 SDHC: CPU revision 0xffffffff
PID:00400002 TID:01370006 SDHC host controller initialize: m_fastPathSDIO:1 m_fastPathSDMEM:0
PID:00400002 TID:01370006 BSPGetDevicePadInfo:board ID 0
PID:00400002 TID:01370006 BSPGetDevicePadInfo: BoardProfile=1,BoardHasDcard=1
PID:00400002 TID:01370006 RequestAndConfigurePadArray+
PID:00400002 TID:01370006 RequestAndConfigurePadArray successfully
PID:00400002 TID:01370006 +GPIO_Backlight::Initialize(Drivers\Active\26)
PID:00400002 TID:01370006 -GPIO_Backlight::Initialize(Drivers\Active\26) == 1
PID:00400002 TID:01370006 TchPdd_Init+
PID:00400002 TID:01370006 PDDInitializeHardware+
PID:00400002 TID:01370006 RequestAndConfigurePadArray+
PID:00400002 TID:01370006 RequestAndConfigurePadArray successfully
PID:00400002 TID:01370006 SX8650_Init+
PID:00400002 TID:01370006 +SX8650Config::InitializeI2CDriver
PID:00400002 TID:01370006 -SX8650Config::InitializeI2CDriver
PID:00400002 TID:01370006 Write: Attempts = 2
PID:00400002 TID:01370006 Write: Attempts = 3
PID:00400002 TID:01370006 Write: Attempts = 4
PID:00400002 TID:01370006 Write: Attempts = 5
PID:00400002 TID:01370006 WARN: I2C: Write failed (SA=0x48, register=0x000000E0)
PID:00400002 TID:01370006 SX8650_Init-
PID:00400002 TID:01370006 TOUCH: touch sysintr:28.
PID:00400002 TID:01370006 PDDInitializeHardware-1
PID:00400002 TID:01370006 TchPdd_Init-
PID:00400002 TID:01370006 -PRU_Init: rc=1
PID:00400002 TID:01370006 RequestDevicePads AM_DEVICE_USB0
PID:00400002 TID:01370006 BSPGetDevicePadInfo:board ID 0
PID:00400002 TID:01370006 BSPGetDevicePadInfo: BoardProfile=1,BoardHasDcard=1
PID:00400002 TID:01370006 RequestAndConfigurePadArray+
PID:00400002 TID:01370006 RequestAndConfigurePadArray successfully
PID:00400002 TID:01370006 CreateUSBOTGObject Drivers\Active\37
PID:00400002 TID:01370006 CAM3xxOTG::Init DEVCTL 98
PID:00400002 TID:01370006 -CAM3xxOTG::Init(1)
PID:00400002 TID:01370006 CAM3xxOTG[1]::FunctionMode(): entering function mode
PID:00400002 TID:01370006 CreateUSBOTGObject Drivers\Active\40
PID:00400002 TID:01370006 CAM3xxOTG::Init DEVCTL 98
PID:00400002 TID:01370006 -CAM3xxOTG::Init(1)
PID:00400002 TID:02D60002 ** ip101a_read_link_status : speed:100000, duplex:fd.
PID:00400002 TID:02D60002 _cpsw3g_phy_update_link, Port:0 LINK:UP SPEED:100 DUPLEX:FD
PID:00400002 TID:04FF0002 BSPGetDevicePadInfo:board ID 0
PID:00400002 TID:04FF0002 BSPGetDevicePadInfo: BoardProfile=1,BoardHasDcard=1
PID:00400002 TID:04FF0002 RequestAndConfigurePadArray+
PID:00400002 TID:04FF0002 RequestAndConfigurePadArray successfully
PID:00400002 TID:04FF0002 Lcdcai::OMAPDisplayController::InitLCD::LcdPdd_LCD_Initialize
PID:00400002 TID:04FF0002 Pclk …………… 300000000
PID:00400002 TID:04FF0002 PVR:getCpuFamily: 5
PID:00400002 TID:04FF0002 PVR:omapsgxddgpe getCpuFamily: 5
PID:00400002 TID:05CC000A TchPdd_Ioctl: IOCTL_TOUCH_ENABLE_TOUCHPANEL
PID:00400002 TID:05CC000A PDDTouchPanelEnable+
PID:00400002 TID:05D6000A PDDTouchIST: IST thread started
PID:00400002 TID:05CC000A PDDTouchPanelEnable-
PID:00400002 TID:02D60002 -> ip101a_reg_dump start:
PID:00400002 TID:02D60002 IP101A Register0: 3100
PID:00400002 TID:02D60002 IP101A Register1: 786d
PID:00400002 TID:02D60002 IP101A Register2: 243
PID:00400002 TID:02D60002 IP101A Register3: c54
PID:00400002 TID:02D60002 IP101A Register4: 1e1
PID:00400002 TID:02D60002 IP101A Register5: 4de1
PID:00400002 TID:02D60002 IP101A Register6: 3
PID:00400002 TID:02D60002 IP101A Register16: 2
PID:00400002 TID:02D60002 IP101A Register17: f00
PID:00400002 TID:02D60002 IP101A Register18: 6c0a
PID:00400002 TID:02D60002 IP101A Register30: 2
PID:00400002 TID:02D60002 -> ip101a_reg_dump end!
PID:00400002 TID:037C0006 OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt() TxIntrHandler
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:037C0006 OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt() TxIntrHandler
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:037C0006 OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt() TxIntrHandler
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:037C0006 OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt() TxIntrHandler
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:037C0006 OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt() TxIntrHandler
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:0269000A OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt() TxIntrHandler
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:037C0006 OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt() TxIntrHandler
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:0269000A OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt() TxIntrHandler
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:0269000A OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt() TxIntrHandler
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:037C0006 OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt() TxIntrHandler
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:037C0006 OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt() TxIntrHandler
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:037C0006 OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt() TxIntrHandler
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:0269000A OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt() TxIntrHandler
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:02B60002 OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt() TxIntrHandler
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:02B60002 OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 OEMInterruptHandler(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt() TxIntrHandler
PID:00400002 TID:03010006 OALIntrDoneIrqs(CPSW Irq 42)
PID:00400002 TID:03010006 ->Cpsw3g_MiniportHandleInterrupt Start:0, 0,
PID:00400002 TID:01740006 kernel PVRSRV_IOCTL_POWER_SET setting state 1
PID:00400002 TID:01740006 PddUpdateBacklight: 1+
PID:00400002 TID:01740006 PddUpdateBacklight-

Steven Liu1：

看了一下你的log，这个地方：你是要把他配成XGMII？我们的335的千兆网只支持RGMII

PID:00400002 TID:01370006 LinkSpeed is not currently supported.PID:00400002 TID:01370006 LinkDuplex is not currently supported.PID:00400002 TID:01370006 Cpsw_read_port_setting: read subkey failed PID:00400002 TID:01370006 Read port settings failedPID:00400002 TID:01370006 Xgmii_sel=45PID:00400002 TID:01370006 Xgmii_sel=45

tony ding：

回复 Steven Liu1:

Dear Steven liu,

appreciate your replying.

maybe my information misguid you. below is my code: as below red colour code, I want use RMII interface control IP101A ic. so I set GMII_SEL = 0x45.

    NdisSetPhysicalAddressHigh(PhysicalAddress2, 0);

NdisSetPhysicalAddressLow (PhysicalAddress2, AM33X_DEVICE_CONF_REGS_PA);

Status = NdisMMapIoSpace((VOID*)&ControlRegsBase, pAdapter->AdapterHandle, PhysicalAddress2, sizeof(AM33X_DEVICE_CONF_REGS));     pControlRegs = NULL;

if(Status == NDIS_STATUS_SUCCESS)

{

pControlRegs=(AM33X_DEVICE_CONF_REGS *)ControlRegsBase;

    RETAILMSG(1,(L"Xgmii_sel=%x\r\n", pControlRegs->GMII_SEL));

pControlRegs->GMII_SEL = 0x45;

RETAILMSG(1,(L"Xgmii_sel=%x\r\n", pControlRegs->GMII_SEL));

}     else     {         RETAILMSG(1,(L"AM33X_DEVICE_CONF_REGS_PA NdisMMapIoSpace fail\r\n"));     }

tony ding：

回复 Steven Liu1:

I want set gmii_sel register to 0x45 value

[AM3359 WinCE7][BSP_WINCE_ARM_A8_02_30_00]Ethernet IP101A with RMII interface

Steven Liu1：

tony ding：

tony ding：

相关推荐

热门标签

热门文章

QQ咨询

回顶部