C5505无法debug

使用的是XDS100仿真器，板子自制，之前一直好用，但突然无法DEBUG，显示

Error connecting to the target:
(Error -1023 @ 0x5F)
Requested JTAG operation failed. Reset the device, and retry the operation. If error persists, confirm configuration, power-cycle the board, and/or try more reliable JTAG settings (e.g. lower TCLK).
(Emulation package 5.1.507.0)

但通过XDS100的Test Connection 的测试结果为

[Start: Texas Instruments XDS100v2 USB Emulator_0]

Execute the command:

%ccs_base%/common/uscif/dbgjtag -f %boarddatafile% -rv -o -F inform,logfile=yes -S pathlength -S integrity

[Result]

—–[Print the board config pathname(s)]————————————

C:\Users\szup\AppData\Local\TEXASI~1\CCS\
ti\0\0\BrdDat\testBoard.dat

—–[Print the reset-command software log-file]—————————–

This utility has selected a 100- or 510-class product.
This utility will load the adapter 'jioserdesusb.dll'.
The library build date was 'May 21 2014'.
The library build time was '17:19:59'.
The library package version is '5.1.507.0'.
The library component version is '35.34.40.0'.
The controller does not use a programmable FPGA.
The controller has a version number of '4' (0x00000004).
The controller has an insertion length of '0' (0x00000000).
This utility will attempt to reset the controller.
This utility has successfully reset the controller.

—–[Print the reset-command hardware log-file]—————————–

The scan-path will be reset by toggling the JTAG TRST signal.
The controller is the FTDI FT2232 with USB interface.
The link from controller to target is direct (without cable).
The software is configured for FTDI FT2232 features.
The controller cannot monitor the value on the EMU[0] pin.
The controller cannot monitor the value on the EMU[1] pin.
The controller cannot control the timing on output pins.
The controller cannot control the timing on input pins.
The scan-path link-delay has been set to exactly '0' (0x0000).

—–[The log-file for the JTAG TCLK output generated from the PLL]———-

There is no hardware for programming the JTAG TCLK frequency.

—–[Measure the source and frequency of the final JTAG TCLKR input]——–

There is no hardware for measuring the JTAG TCLK frequency.

—–[Perform the standard path-length test on the JTAG IR and DR]———–

This path-length test uses blocks of 512 32-bit words.

The test for the JTAG IR instruction path-length succeeded.
The JTAG IR instruction path-length is 38 bits.

The test for the JTAG DR bypass path-length succeeded.
The JTAG DR bypass path-length is 1 bits.

—–[Perform the Integrity scan-test on the JTAG IR]————————

This test will use blocks of 512 32-bit words.
This test will be applied just once.

Do a test using 0xFFFFFFFF.
Scan tests: 1, skipped: 0, failed: 0
Do a test using 0x00000000.
Scan tests: 2, skipped: 0, failed: 0
Do a test using 0xFE03E0E2.
Scan tests: 3, skipped: 0, failed: 0
Do a test using 0x01FC1F1D.
Scan tests: 4, skipped: 0, failed: 0
Do a test using 0x5533CCAA.
Scan tests: 5, skipped: 0, failed: 0
Do a test using 0xAACC3355.
Scan tests: 6, skipped: 0, failed: 0
All of the values were scanned correctly.

The JTAG IR Integrity scan-test has succeeded.

—–[Perform the Integrity scan-test on the JTAG DR]————————

This test will use blocks of 512 32-bit words.
This test will be applied just once.

Do a test using 0xFFFFFFFF.
Scan tests: 1, skipped: 0, failed: 0
Do a test using 0x00000000.
Scan tests: 2, skipped: 0, failed: 0
Do a test using 0xFE03E0E2.
Scan tests: 3, skipped: 0, failed: 0
Do a test using 0x01FC1F1D.
Scan tests: 4, skipped: 0, failed: 0
Do a test using 0x5533CCAA.
Scan tests: 5, skipped: 0, failed: 0
Do a test using 0xAACC3355.
Scan tests: 6, skipped: 0, failed: 0
All of the values were scanned correctly.

The JTAG DR Integrity scan-test has succeeded.

[End: Texas Instruments XDS100v2 USB Emulator_0]

请大家帮忙看看这是什么问题，十分感谢！

Shine：

量一下c5505 clkout管脚看DSP是否跑起来了？

Zheng Shi1：

回复 Shine:

板子设计的时候没有留clkout的测量接口，有没有其他方法看看哪里有问题？

Shine：

回复 Zheng Shi1:

可以量一下JTAG口信号看是否正确？

Zheng Shi1：

回复 Shine:

你好，有时在debug的时候按一下复位键可以连上dsp芯片，这会是什么原因呢？

Tony Tang：

回复 Zheng Shi1:

可能是上电与复位时序不对。复位信号释放提前于电源稳定。

Zheng Shi1：

回复 Tony Tang:

虽然可以连上，但是调试的时候会提示：

C55xx: Trouble Halting Target CPU: (Error -1141 @ 0x0) Device is not responding to the request. Reset the device, and retry the operation. If error persists, confirm configuration, power-cycle the board, and/or try more reliable JTAG settings (e.g. lower TCLK). (Emulation package 5.1.507.0) 

Shine：

回复 Zheng Shi1:

把reset信号线拉长，从电源和时钟稳定后开始算有效时间。

Zheng Shi1：

回复 Shine:

我的复位使用的IMP706芯片，复位应该不会有问题。