TI中文支持网
TI专业的中文技术问题搜集分享网站

WOR的RX是否可以直接切换TX

TI工程师您好。我现在正在调试WakeOnRadio,现在由WOR切换到直接接受模式是可以的,但是我现在还需要一个功能就是直接由RX切换到TX模式,使用预定的接受到数据后直接切换到TX,是可行的。我现在发现该方法还是不太适用于我的案例,也就是在接受到数据后,需要判断是否进行发送,也就是判断正确才会进行下发数据。请问该如何操作呢?谢谢!

/***** Function definitions *****/ /* RX task function. Executed in Task context by TI-RTOS when the scheduler starts. */

void *mainThread(void *arg0) { RF_Params rfParams; RF_Params_init(&rfParams);

/* Open LED pins */

ledPinHandle = PIN_open(&ledPinState, pinTable);

if (ledPinHandle == NULL) { while(1); }

/* Route out LNA active pin to LED1 */

 PINCC26XX_setMux(ledPinHandle, Board_PIN_LED0, PINCC26XX_MUX_RFC_GPO0);

/* Create queue and data entries */

if (RFQueue_defineQueue(&dataQueue, rxDataEntryBuffer, sizeof(rxDataEntryBuffer), NUM_DATA_ENTRIES, MAX_LENGTH + NUM_APPENDED_BYTES)) { /* Failed to allocate space for all data entries */ while(1); }

/* Copy all RX options from the SmartRF Studio exported RX command to the RX Sniff command */

initializeSniffCmdFromRxCmd(&RF_cmdPropRxSniff, &RF_cmdPropRx);

/* Configure RX part of RX_SNIFF command */

RF_cmdPropRxSniff.pQueue = &dataQueue;

RF_cmdPropRxSniff.pOutput = (uint8_t*)&rxStatistics; RF_cmdPropRxSniff.maxPktLen = MAX_LENGTH;

/* Discard ignored packets and CRC errors from Rx queue */

 RF_cmdPropRxSniff.rxConf.bAutoFlushIgnored = 1;

RF_cmdPropRxSniff.rxConf.bAutoFlushCrcErr = 1;

/* Calculate datarate from prescaler and rate word */

 uint32_t datarate = calculateSymbolRate(RF_cmdPropRadioDivSetup.symbolRate.preScale, RF_cmdPropRadioDivSetup.symbolRate.rateWord);

/* Configure Sniff-mode part of the RX_SNIFF command */

configureSniffCmd(&RF_cmdPropRxSniff, WOR_MODE, datarate, WOR_WAKEUPS_PER_SECOND);

/* Request access to the radio */

 rfHandle = RF_open(&rfObject, &RF_prop, (RF_RadioSetup*)&RF_cmdPropRadioDivSetup, &rfParams);

/* Set frequency */

RF_runCmd(rfHandle, (RF_Op*)&RF_cmdFs, RF_PriorityNormal, &callback, 0);

/* Save the current radio time */

RF_cmdPropRxSniff.startTime = RF_getCurrentTime();

/* Enter main loop */

while(1) {

/* Set next wakeup time in the future */

RF_cmdPropRxSniff.startTime += WOR_WAKE_UP_INTERVAL_RAT_TICKS(WOR_WAKEUPS_PER_SECOND);

/* Schedule RX */

RF_runCmd(rfHandle, (RF_Op*)&RF_cmdPropRxSniff, RF_PriorityNormal, &callback, RF_EventRxEntryDone);

/* Log RX_SNIFF status */

switch(RF_cmdPropRxSniff.status)

 {

case PROP_DONE_IDLE:

/* Idle based on RSSI */

worStatistics.doneIdle++; break;

case PROP_DONE_IDLETIMEOUT:

/* Idle based on PQT */

worStatistics.doneIdleTimeout++;

break;

case PROP_DONE_RXTIMEOUT: /

* Got valid preamble on the air, but did not find sync word */

worStatistics.doneRxTimeout++; break;

case PROP_DONE_OK:

 /* Received packet */

worStatistics.doneOk++;

//进入发送模式,烦请指点下

……. break;

default:

/* Unhandled status */

break;

};

}

}

Viki Shi:

请参考置顶帖中的例程,包含RX TX切换: http://www.deyisupport.com/question_answer/wireless_connectivity/f/45/t/106253.aspx

user5093767:

您好,请问怎么从这个模式,切换到发送模式呢,看链接的程序,还是没有搞懂

赞(0)
未经允许不得转载:TI中文支持网 » WOR的RX是否可以直接切换TX
分享到: 更多 (0)