TI中文支持网C2000-GANG,驱动正常，通电正常，软件最新版本，运行时 点保存或者支行直接跳出错误 ，或者闪退。
TDI Fuse keys 1-8 全是error
Susan Yang：
请问您是否有进行Self Test？
如 www.ti.com/…/spruhs0c.pdf
的 2.4 Self Test
所示，是否是成功的？若是不成功的话，请上传以下您的test report文件，谢谢
user1616268：
回复 Susan Yang:
有进行检测，
=== C2000-GANG Self test results ( Thursday, May 14, 2020, 14:26:32 ) ===
Adapter SN ——: 17101253 Hardware ——–: C2K : 01.04Access key ——: C2000 – Gang Programmer Silicon Number –: 8A26 1147 0C00 2B00API Firmware —-: C2K-Gang AC28: 01.00.04.06BOOT Firmware —: G430BOOT B430: 01.00.02.00GUI Software —-: C2000-Gang-GUI G28x: 01.00.03.00DLL Software —-: C2000-Gang-DLL D280: 01.00.03.00
================ Test results =============
No. name parameter limits result status
1: Data Bus (ALL LOW) 0x0000 (0x0000 – 0x0000) Result: 0x00 … >> OK << 2: Data Bus (ALL HIGH) 0x00FF (0xFFFF – 0xFFFF) Result: 0xFFFF … >> OK << 3: Data Bus (D-0 HI ) 0x0001 (0x0101 – 0x0101) Result: 0x0101 … >> OK << 4: Data Bus (D-1 HI ) 0x0002 (0x0202 – 0x0202) Result: 0x0202 … >> OK << 5: Data Bus (D-2 HI ) 0x0004 (0x0404 – 0x0404) Result: 0x0404 … >> OK << 6: Data Bus (D-3 HI ) 0x0008 (0x0808 – 0x0808) Result: 0x0808 … >> OK << 7: Data Bus (D-4 HI ) 0x0010 (0x1010 – 0x1010) Result: 0x1010 … >> OK << 8: Data Bus (D-5 HI ) 0x0020 (0x2020 – 0x2020) Result: 0x2020 … >> OK << 9: Data Bus (D-6 HI ) 0x0040 (0x4040 – 0x4040) Result: 0x4040 … >> OK << 10: Data Bus (D-7 HI ) 0x0080 (0x8080 – 0x8080) Result: 0x8080 … >> OK <<
11: Data-2 Bus (ALL LOW) 0x0000 (0x0000 – 0x0000) Result: 0x00 … >> OK << 12: Data-2 Bus (ALL HIGH) 0x00FF (0xFFFF – 0xFFFF) Result: 0xFFFF … >> OK << 13: Data-2 Bus (D2-0 HI ) 0x0001 (0x0101 – 0x0101) Result: 0x0101 … >> OK << 14: Data-2 Bus (D2-1 HI ) 0x0002 (0x0202 – 0x0202) Result: 0x0202 … >> OK << 15: Data-2 Bus (D2-2 HI ) 0x0004 (0x0404 – 0x0404) Result: 0x0404 … >> OK << 16: Data-2 Bus (D2-3 HI ) 0x0008 (0x0808 – 0x0808) Result: 0x0808 … >> OK << 17: Data-2 Bus (D2-4 HI ) 0x0010 (0x1010 – 0x1010) Result: 0x1010 … >> OK << 18: Data-2 Bus (D2-5 HI ) 0x0020 (0x2020 – 0x2020) Result: 0x2020 … >> OK << 19: Data-2 Bus (D2-6 HI ) 0x0040 (0x4040 – 0x4040) Result: 0x4040 … >> OK << 20: Data-2 Bus (D2-7 HI ) 0x0080 (0x8080 – 0x8080) Result: 0x8080 … >> OK <<
21: Vcc Target-1 (ALL OFF) 0.00 V ( 0.00 to 0.30) Result: 3.29 V … >> ERROR << 22: Vcc Target-2 (ALL OFF) 0.00 V ( 0.00 to 0.30) Result: 0.02 V … >> OK << 23: Vcc Target-3 (ALL OFF) 0.00 V ( 0.00 to 0.30) Result: 0.01 V … >> OK << 24: Vcc Target-4 (ALL OFF) 0.00 V ( 0.00 to 0.30) Result: 0.01 V … >> OK << 25: Vcc Target-5 (ALL OFF) 0.00 V ( 0.00 to 0.30) Result: 0.01 V … >> OK << 26: Vcc Target-6 (ALL OFF) 0.00 V ( 0.00 to 0.30) Result: 0.01 V … >> OK << 27: Vcc Target-7 (ALL OFF) 0.00 V ( 0.00 to 0.30) Result: 0.01 V … >> OK << 28: Vcc Target-8 (ALL OFF) 0.00 V ( 0.00 to 0.30) Result: 0.01 V … >> OK <<
29: Translators VT (OFF) 0.00 V ( 0.00 to 0.50) Result: 0.01 V … >> OK << 30: Translators VT (ON 3.3V) 3.30 V ( 3.10 to 3.50) Result: 3.24 V … >> OK <<
31: Vpp Voltage-in 10.00 V ( 8.00 to 12.00) Result: 10.75 V … >> OK << 32: Vpp Voltage 7.00 V ( 6.50 to 7.30) Result: 6.86 V … >> OK << 33: Internal Vcc-3.3V 3.30 V ( 3.20 to 3.40) Result: 3.31 V … >> OK <<
34: Vcc Target-1 (ALL ON 3.3V) 3.30 V ( 3.10 to 3.50) Result: 3.29 V … >> OK << 35: Vcc Target-2 (ALL ON 3.3V) 3.30 V ( 3.10 to 3.50) Result: 0.13 V … >> ERROR << 36: Vcc Target-3 (ALL ON 3.3V) 3.30 V ( 3.10 to 3.50) Result: 0.12 V … >> ERROR << 37: Vcc Target-4 (ALL ON 3.3V) 3.30 V ( 3.10 to 3.50) Result: 0.12 V … >> ERROR << 38: Vcc Target-5 (ALL ON 3.3V) 3.30 V ( 3.10 to 3.50) Result: 0.12 V … >> ERROR << 39: Vcc Target-6 (ALL ON 3.3V) 3.30 V ( 3.10 to 3.50) Result: 0.12 V … >> ERROR << 40: Vcc Target-7 (ALL ON 3.3V) 3.30 V ( 3.10 to 3.50) Result: 0.12 V … >> ERROR << 41: Vcc Target-8 (ALL ON 3.3V) 3.30 V ( 3.10 to 3.50) Result: 0.12 V … >> ERROR <<
42: Vcc discharge (50ms)Target-1 3.30 V ( 0.30 to 1.50) Result: 3.29 V … >> ERROR << 43: Vcc discharge (50ms)Target-2 3.30 V ( 0.30 to 1.50) Result: 0.17 V … >> ERROR << 44: Vcc discharge (50ms)Target-3 3.30 V ( 0.30 to 1.50) Result: 0.16 V … >> ERROR << 45: Vcc discharge (50ms)Target-4 3.30 V ( 0.30 to 1.50) Result: 0.17 V … >> ERROR << 46: Vcc discharge (50ms)Target-5 3.30 V ( 0.30 to 1.50) Result: 0.16 V … >> ERROR << 47: Vcc discharge (50ms)Target-6 3.30 V ( 0.30 to 1.50) Result: 0.16 V … >> ERROR << 48: Vcc discharge (50ms)Target-7 3.30 V ( 0.30 to 1.50) Result: 0.17 V … >> ERROR << 49: Vcc discharge (50ms)Target-8 3.30 V ( 0.30 to 1.50) Result: 0.16 V … >> ERROR <<
50: Vcc Target-1 ( #1 ON ) 0.00 V ( 3.10 to 3.50) Result: 3.29 V … >> OK << 51: Vcc Target-2 ( #1 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 52: Vcc Target-3 ( #1 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 53: Vcc Target-4 ( #1 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 54: Vcc Target-5 ( #1 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 55: Vcc Target-6 ( #1 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 56: Vcc Target-7 ( #1 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 57: Vcc Target-8 ( #1 ON ) 3.30 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 58: Vcc Target-1 ( #2 ON ) 0.00 V ( 0.00 to 0.50) Result: 3.29 V … >> ERROR << 59: Vcc Target-2 ( #2 ON ) 0.00 V ( 3.10 to 3.50) Result: 0.17 V … >> ERROR << 60: Vcc Target-3 ( #2 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 61: Vcc Target-4 ( #2 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 62: Vcc Target-5 ( #2 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 63: Vcc Target-6 ( #2 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 64: Vcc Target-7 ( #2 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 65: Vcc Target-8 ( #2 ON ) 3.30 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 66: Vcc Target-1 ( #3 ON ) 0.00 V ( 0.00 to 0.50) Result: 3.29 V … >> ERROR << 67: Vcc Target-2 ( #3 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 68: Vcc Target-3 ( #3 ON ) 0.00 V ( 3.10 to 3.50) Result: 0.17 V … >> ERROR << 69: Vcc Target-4 ( #3 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 70: Vcc Target-5 ( #3 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 71: Vcc Target-6 ( #3 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 72: Vcc Target-7 ( #3 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 73: Vcc Target-8 ( #3 ON ) 3.30 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 74: Vcc Target-1 ( #4 ON ) 0.00 V ( 0.00 to 0.50) Result: 3.29 V … >> ERROR << 75: Vcc Target-2 ( #4 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 76: Vcc Target-3 ( #4 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 77: Vcc Target-4 ( #4 ON ) 0.00 V ( 3.10 to 3.50) Result: 0.16 V … >> ERROR << 78: Vcc Target-5 ( #4 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 79: Vcc Target-6 ( #4 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 80: Vcc Target-7 ( #4 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 81: Vcc Target-8 ( #4 ON ) 3.30 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 82: Vcc Target-1 ( #5 ON ) 0.00 V ( 0.00 to 0.50) Result: 3.29 V … >> ERROR << 83: Vcc Target-2 ( #5 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 84: Vcc Target-3 ( #5 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 85: Vcc Target-4 ( #5 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 86: Vcc Target-5 ( #5 ON ) 0.00 V ( 3.10 to 3.50) Result: 0.16 V … >> ERROR << 87: Vcc Target-6 ( #5 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 88: Vcc Target-7 ( #5 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 89: Vcc Target-8 ( #5 ON ) 3.30 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 90: Vcc Target-1 ( #6 ON ) 0.00 V ( 0.00 to 0.50) Result: 3.29 V … >> ERROR << 91: Vcc Target-2 ( #6 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 92: Vcc Target-3 ( #6 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 93: Vcc Target-4 ( #6 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 94: Vcc Target-5 ( #6 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 95: Vcc Target-6 ( #6 ON ) 0.00 V ( 3.10 to 3.50) Result: 0.16 V … >> ERROR << 96: Vcc Target-7 ( #6 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 97: Vcc Target-8 ( #6 ON ) 3.30 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 98: Vcc Target-1 ( #7 ON ) 0.00 V ( 0.00 to 0.50) Result: 3.29 V … >> ERROR << 99: Vcc Target-2 ( #7 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK <<100: Vcc Target-3 ( #7 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK <<101: Vcc Target-4 ( #7 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK <<102: Vcc Target-5 ( #7 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK <<103: Vcc Target-6 ( #7 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK <<104: Vcc Target-7 ( #7 ON ) 0.00 V ( 3.10 to 3.50) Result: 0.17 V … >> ERROR <<105: Vcc Target-8 ( #7 ON ) 3.30 V ( 0.00 to 0.50) Result: 0.16 V … >> OK <<106: Vcc Target-1 ( #8 ON ) 0.00 V ( 0.00 to 0.50) Result: 3.29 V … >> ERROR <<107: Vcc Target-2 ( #8 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK <<108: Vcc Target-3 ( #8 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK <<109: Vcc Target-4 ( #8 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK <<110: Vcc Target-5 ( #8 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK <<111: Vcc Target-6 ( #8 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK <<112: Vcc Target-7 ( #8 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK <<113: Vcc Target-8 ( #8 ON ) 3.30 V ( 3.10 to 3.50) Result: 0.16 V … >> ERROR <<
114: SD Power OFF 0x0000 (0x0000 – 0x0000) Result: 0x00 … >> OK <<115: SD Power ON 0x0001 (0x0001 – 0x0001) Result: 0x01 … >> OK <<116: SD Discharge – delay 2ms 0x0010 (0x0001 – 0x0001) Result: 0x01 … >> OK <<117: SD Discharge – delay 50ms 0x0010 (0x0000 – 0x0000) Result: 0x00 … >> OK <<
118: BSL RX bus (#1 HIGH) 0x0001 (0x0001 – 0x0001) Result: 0x01 … >> OK <<119: BSL RX bus (#2 HIGH) 0x0002 (0x0002 – 0x0002) Result: 0x02 … >> OK <<120: BSL RX bus (#3 HIGH) 0x0004 (0x0004 – 0x0004) Result: 0x04 … >> OK <<121: BSL RX bus (#4 HIGH) 0x0008 (0x0008 – 0x0008) Result: 0x08 … >> OK <<122: BSL RX bus (#5 HIGH) 0x0010 (0x0010 – 0x0010) Result: 0x10 … >> OK <<123: BSL RX bus (#6 HIGH) 0x0020 (0x0020 – 0x0020) Result: 0x20 … >> OK <<124: BSL RX bus (#7 HIGH) 0x0040 (0x0040 – 0x0040) Result: 0x40 … >> OK <<125: BSL RX bus (#8 HIGH) 0x0080 (0x0080 – 0x0080) Result: 0x80 … >> OK <<
126: BSL TX bus (#1 HIGH) 0x0001 (0x0001 – 0x0001) Result: 0x01 … >> OK <<127: BSL TX bus (#2 HIGH) 0x0002 (0x0002 – 0x0002) Result: 0x02 … >> OK <<128: BSL TX bus (#3 HIGH) 0x0004 (0x0004 – 0x0004) Result: 0x04 … >> OK <<129: BSL TX bus (#4 HIGH) 0x0008 (0x0008 – 0x0008) Result: 0x08 … >> OK <<130: BSL TX bus (#5 HIGH) 0x0010 (0x0010 – 0x0010) Result: 0x10 … >> OK <<131: BSL TX bus (#6 HIGH) 0x0020 (0x0020 – 0x0020) Result: 0x20 … >> OK <<132: BSL TX bus (#7 HIGH) 0x0040 (0x0040 – 0x0040) Result: 0x40 … >> OK <<133: BSL TX bus (#8 HIGH) 0x0080 (0x0080 – 0x0080) Result: 0x80 … >> OK <<
134: TDI bus (#8 HIGH) 0x0080 (0x0080 – 0x0080) Result: 0x81 … >> ERROR <<135: TDI bus (#1 HIGH) 0x0001 (0x0001 – 0x0001) Result: 0x01 … >> OK <<136: TDI bus (#2 HIGH) 0x0002 (0x0002 – 0x0002) Result: 0x03 … >> ERROR <<137: TDI bus (#3 HIGH) 0x0004 (0x0004 – 0x0004) Result: 0x05 … >> ERROR <<138: TDI bus (#4 HIGH) 0x0008 (0x0008 – 0x0008) Result: 0x09 … >> ERROR <<139: TDI bus (#5 HIGH) 0x0010 (0x0010 – 0x0010) Result: 0x11 … >> ERROR <<140: TDI bus (#6 HIGH) 0x0020 (0x0020 – 0x0020) Result: 0x21 … >> ERROR <<141: TDI bus (#7 HIGH) 0x0040 (0x0040 – 0x0040) Result: 0x41 … >> ERROR <<
142: TDIO Tx-bus (#1 HIGH) 0x0001 (0x0001 – 0x0001) Result: 0x01 … >> OK <<143: TDIO Tx-bus (#2 HIGH) 0x0002 (0x0002 – 0x0002) Result: 0x02 … >> OK <<144: TDIO Tx-bus (#3 HIGH) 0x0004 (0x0004 – 0x0004) Result: 0x04 … >> OK <<145: TDIO Tx-bus (#4 HIGH) 0x0008 (0x0008 – 0x0008) Result: 0x08 … >> OK <<146: TDIO Tx-bus (#5 HIGH) 0x0010 (0x0010 – 0x0010) Result: 0x10 … >> OK <<147: TDIO Tx-bus (#6 HIGH) 0x0020 (0x0020 – 0x0020) Result: 0x20 … >> OK <<148: TDIO Tx-bus (#7 HIGH) 0x0040 (0x0040 – 0x0040) Result: 0x40 … >> OK <<149: TDIO Tx-bus (#8 HIGH) 0x0080 (0x0080 – 0x0080) Result: 0x80 … >> OK <<
150: TDIO Tx-Rx (#1 HIGH) 0x0001 (0x0001 – 0x0001) Result: 0x01 … >> OK <<151: TDIO Tx-Rx (#2 HIGH) 0x0002 (0x0002 – 0x0002) Result: 0x02 … >> OK <<152: TDIO Tx-Rx (#3 HIGH) 0x0004 (0x0004 – 0x0004) Result: 0x04 … >> OK <<153: TDIO Tx-Rx (#4 HIGH) 0x0008 (0x0008 – 0x0008) Result: 0x08 … >> OK <<154: TDIO Tx-Rx (#5 HIGH) 0x0010 (0x0010 – 0x0010) Result: 0x10 … >> OK <<155: TDIO Tx-Rx (#6 HIGH) 0x0020 (0x0020 – 0x0020) Result: 0x20 … >> OK <<156: TDIO Tx-Rx (#7 HIGH) 0x0040 (0x0040 – 0x0040) Result: 0x40 … >> OK <<157: TDIO Tx-Rx (#8 HIGH) 0x0080 (0x0080 – 0x0080) Result: 0x80 … >> OK <<
158: TDIO Rx-bus (#1 HIGH) 0x0001 (0x0001 – 0x0001) Result: 0x01 … >> OK <<159: TDIO Rx-bus (#2 HIGH) 0x0002 (0x0002 – 0x0002) Result: 0x02 … >> OK <<160: TDIO Rx-bus (#3 HIGH) 0x0004 (0x0004 – 0x0004) Result: 0x04 … >> OK <<161: TDIO Rx-bus (#4 HIGH) 0x0008 (0x0008 – 0x0008) Result: 0x08 … >> OK <<162: TDIO Rx-bus (#5 HIGH) 0x0010 (0x0010 – 0x0010) Result: 0x10 … >> OK <<163: TDIO Rx-bus (#6 HIGH) 0x0020 (0x0020 – 0x0020) Result: 0x20 … >> OK <<164: TDIO Rx-bus (#7 HIGH) 0x0040 (0x0040 – 0x0040) Result: 0x40 … >> OK <<165: TDIO Rx-bus (#84 HIGH) 0x0080 (0x0080 – 0x0080) Result: 0x80 … >> OK <<
166: TMS bus (All HIGH) 0x00FF (0x00FF – 0x00FF) Result: 0xFF … >> OK <<167: TMS bus (All LOW) 0x0000 (0x0000 – 0x0000) Result: 0x00 … >> OK <<
168: TMS bus (#1 HIGH) 0x0001 (0x0001 – 0x0001) Result: 0x01 … >> OK <<169: TMS bus (#2 HIGH) 0x0002 (0x0002 – 0x0002) Result: 0x02 … >> OK <<170: TMS bus (#3 HIGH) 0x0004 (0x0004 – 0x0004) Result: 0x04 … >> OK <<171: TMS bus (#4 HIGH) 0x0008 (0x0008 – 0x0008) Result: 0x08 … >> OK <<172: TMS bus (#5 HIGH) 0x0010 (0x0010 – 0x0010) Result: 0x10 … >> OK <<173: TMS bus (#6 HIGH) 0x0020 (0x0020 – 0x0020) Result: 0x20 … >> OK <<174: TMS bus (#7 HIGH) 0x0040 (0x0040 – 0x0040) Result: 0x40 … >> OK <<175: TMS bus (#8 HIGH) 0x0080 (0x0080 – 0x0080) Result: 0x80 … >> OK <<
176: RST bus (All HIGH) 0x00FF (0x00FF – 0x00FF) Result: 0xFF … >> OK <<177: RST bus (All LOW) 0x0000 (0x0000 – 0x0000) Result: 0x00 … >> OK <<
178: RST bus (#1 HIGH) 0x0001 (0x0001 – 0x0001) Result: 0x00 … >> ERROR <<179: RST bus (#2 HIGH) 0x0002 (0x0002 – 0x0002) Result: 0x02 … >> OK <<180: RST bus (#3 HIGH) 0x0004 (0x0004 – 0x0004) Result: 0x04 … >> OK <<181: RST bus (#4 HIGH) 0x0008 (0x0008 – 0x0008) Result: 0x08 … >> OK <<182: RST bus (#5 HIGH) 0x0010 (0x0010 – 0x0010) Result: 0x10 … >> OK <<183: RST bus (#6 HIGH) 0x0020 (0x0020 – 0x0020) Result: 0x20 … >> OK <<184: RST bus (#7 HIGH) 0x0040 (0x0040 – 0x0040) Result: 0x40 … >> OK <<185: RST bus (#8 HIGH) 0x0080 (0x0080 – 0x0080) Result: 0x80 … >> OK <<
186: Keys buffer (All pull-up) 0x001F (0x001F – 0x001F) Result: 0x1F … >> OK <<
187: Access to LCD RAM (0xAA) 0x00AA (0x00AA – 0x00AA) Result: 0xAA … >> OK <<188: Access to LCD RAM (0x99) 0x0099 (0x0099 – 0x0099) Result: 0x99 … >> OK <<
189: Image Flash Access (get ID) 0x0002 (0x0001 – 0x0002) Result: 0x00 … >> ERROR <<
190: TDI Fuse keys (#1 ON) 0x0001 (0x0001 – 0x0001) Result: 0x01 … >> OK <<191: TDI Fuse keys (#2 ON) 0x0002 (0x0002 – 0x0002) Result: 0x03 … >> ERROR <<192: TDI Fuse keys (#3 ON) 0x0004 (0x0004 – 0x0004) Result: 0x05 … >> ERROR <<193: TDI Fuse keys (#4 ON) 0x0008 (0x0008 – 0x0008) Result: 0x09 … >> ERROR <<194: TDI Fuse keys (#5 ON) 0x0010 (0x0010 – 0x0010) Result: 0x11 … >> ERROR <<195: TDI Fuse keys (#6 ON) 0x0020 (0x0020 – 0x0020) Result: 0x21 … >> ERROR <<196: TDI Fuse keys (#7 ON) 0x0040 (0x0040 – 0x0040) Result: 0x41 … >> ERROR <<197: TDI Fuse keys (#8 ON) 0x0080 (0x0080 – 0x0080) Result: 0x81 … >> ERROR <<
198: TEST Fuse keys (#1 ON) 1.00 ( 2.80 to 3.50) Result: 0.00 … >> ERROR <<199: TEST Fuse keys (#2 ON) 2.00 ( 2.80 to 3.50) Result: 0.00 … >> ERROR <<200: TEST Fuse keys (#3 ON) 3.00 ( 2.80 to 3.50) Result: 0.00 … >> ERROR <<201: TEST Fuse keys (#4 ON) 4.00 ( 2.80 to 3.50) Result: 0.00 … >> ERROR <<202: TEST Fuse keys (#5 ON) 5.00 ( 2.80 to 3.50) Result: 0.00 … >> ERROR <<203: TEST Fuse keys (#6 ON) 6.00 ( 2.80 to 3.50) Result: 0.00 … >> ERROR <<204: TEST Fuse keys (#7 ON) 7.00 ( 2.80 to 3.50) Result: 0.00 … >> ERROR <<205: TEST Fuse keys (#8 ON) 8.00 ( 2.80 to 3.50) Result: 0.00 … >> ERROR <<
============== Finished =================================* Test failed!! 54 error(s).
Susan Yang：
回复 user1616268:
您现在是连接板子测试的？
The Gang Splitter must be connected to the C2000 Gang Programmer. Disconnect all target devices, because any connected devices can modify the test results and make them invalid.
user1616268：
回复 Susan Yang:
是的，现在就是连接目标板 点存储程序后 错误或者直接闪退。
user1616268：
回复 user1616268:
Susan Yang：
回复 user1616268:
很抱歉，可能我之前描述的有问题
您现在测试self test 的时候是否连接板子？ self test 时是不可以连接板子的
我们现在应该先确认self test 的时候是可以正常通过的，即 C2000-GANG Self test results 这个报告是正确的，以确保C2000 GANG本身硬件以及功能是没有问题的
user1616268：
回复 Susan Yang:
不连接板子测试是OK的，连接板子 对软件编程时出现闪退 和报错
user1616268：
回复 user1616268:
现在就是连接板子 对器件 编程 闪退，文件也保存不了验证删除也操作不了 直接就闪退
user1616268：
回复 user1616268:
user1616268：
回复 user1616268:
还有电脑上驱动显示的是MSP-GANG的，，这个设备是C2000-GANG 为什么，
