TI中文支持网TI大神和大牛童鞋帮忙看下是哪里有问题,两个ICE3359一个做主一个做从，小弟谢谢啦 还有acontics配置导出工具，或者ICE3359 v2.1 按照acontics主站导出编辑好的ENI.c谁能发个链接，不尽感谢 。
TWINCAT 两个从站测试没有问题可以控制LED。
TI Industrial SDK Version – IASDK 1.1.0.8
Device name : AM3359
Chip Revision : AM335x ES1.2 [PG2.1]
SYS/BIOS EcMaster Sample application running on ICE V2Full command line: -auxclk 2000 -v 2 -t 10000 -perf -cpsw 1 1 1 m custom am33XX 1 1 0
001151 : Run demo now with cycle time 2000 usec
001151 : Using AuxClock
001151 : ==========================
001151 : Initialize EtherCAT Master
001151 : ==========================
001151 : EC-Master V2.9.0.06 (Protected) for SYSBIOS Copyright acontis technologies GmbH @ 2016
001152 : CPSW INF: Port 1, Prio 1, Flags [Polling] [Master], Phy 1, PhyInterface 32, MAC 68:c9:0b:1c:83:22
001153 : CPSW INF: CPSW3G found. CPSW INF: HW-Id: 0x0019, RTL: 0, Major: 1, Minor: 0xc
001154 : CPSW INF: PHY found. Id=0x2000a211
001154 : CPSW INF: Restart PHY auto negotiation
007214 : CPSW INF: PHY link timeout (waiting for auto negotiation completion).
007232 : Unlicensed version, stop sending ethernet frames after 60 minutes!
007234 : Ethernet cable not connected
007243 : ecatScanBus() Error 0x9811002d in McSm state 'SB_DONE' for requested state 'SB_DONE'
007243 : Cannot scan bus: ERROR: Ethernet link cable disconnected (0x9811002d)
007243 : EtherCAT network adapter MAC: 68-C9-0B-1C-83-22
007243 : =====================
007243 : Start EtherCAT Master
007243 : =====================
007273 : ecatSetMasterStateEx() Error 0x9811002d in McSm state 'START' for requested state 'START'
007273 : Scan bus mismatch for the first slave on the bus! BUS VendorId: —- (0x0); ProductCode: Unknown (0x0).
007273 : CFG/BUS VendorId: —- (0xe000059d) / —- (0x0); ProductCode: Unknown (0x54490002) / Unknown (0x0)
007273 : Scan bus mismatch for the first slave on the bus! BUS VendorId: —- (0x0); ProductCode: Unknown (0x0).
007273 : CFG/BUS VendorId: —- (0xe000059d) / —- (0x0); ProductCode: Unknown (0x54490002) / Unknown (0x0)
007273 : Scan bus mismatch for the first slave on the bus! BUS VendorId: —- (0x0); ProductCode: Unknown (0x0).
007273 : CFG/BUS VendorId: —- (0xe000059d) / —- (0x0); ProductCode: Unknown (0x54490002) / Unknown (0x0)
007273 : Cannot start set master state to INIT (Result = ERROR: Ethernet link cable disconnected (0x9811002d))
007273 : ========================
007273 : Shutdown EtherCAT Master
007273 : ========================
007361 : ecatSetMasterStateEx() Error 0x9811002d in McSm state 'START' for requested state 'START'
007361 : Cannot stop EtherCAT-Master! ERROR: Ethernet link cable disconnected (0x9811002d)
007379 : ================================================================
007379 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 0.8/ 10.8
007379 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 1.2/ 46.2
007379 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 2.5/ 95.7
007379 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 0.4/ 4.6
007379 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 952.9/2005.2
007379 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.4/ 4.8
007676 : CPSW INF: Disable running RX-DMA
007676 : CPSW INF: RX+TX DMA disabled. Delay 500
007677 : EcMasterDemo stop.
Jian Zhou：
请问有参考过这篇文档么：
http://www.ti.com/lit/ug/tiduaf8a/tiduaf8a.pdf
tao zhang16：
回复 Jian Zhou:
是参考这个文档做的，目前因为下载不到EC-engineer所以，使用ICE3359做从站，尝试用1.1.0.8sdk slave demo带的eni文件，应该是不通用，，能不能给个EC engineer tool 或者给个，ICE3359V2的 acontic 环境的ENI文件
tao zhang16：
回复 Jian Zhou:
ENI文件必须用acontis EC engineer 生成吗
Jian Zhou：
回复 tao zhang16:
这个问题我会联系acontics的工程师，看看能否把相关软件工具在论坛里共享一下。
Jian Zhou：
回复 Jian Zhou:
关于Acontics的EC engineer工具，请通过如下联系方式本地获取：
北京盟通科技有限公司：www.motrotech.com， tel： 010-62740270， Email： info@motrotech.com
tao zhang16：
回复 Jian Zhou:
感谢楼主Jason Lee 和TI工程师一直的帮助。 目前联系到了代理，拿到了EC engineer工具 使用ICE3359 V2作为ETHERCAT从站导入sdk2.0.1.2 salveDemo里的TIeni.xml ECengineer 能够找到从站 并导出ENI.xml 使用bin2header 生成eni.c后替换acontis 2.9 MasterDemo的eni.c 编译，连接从站后执行， 还是报错 ethernet cable not connect 还请指点一下。谢啦
01151 : ==========================
001151 : Initialize EtherCAT Master
001151 : ==========================
001151 : EC-Master V2.9.0.06 (Protected) for SYSBIOS Copyright acontis technologies GmbH @ 2016
001152 : CPSW INF: Port 1, Prio 1, Flags [Polling] [Master], Phy 1, PhyInterface 32,MAC 68:c9:0b:1c:83:22
001153 : CPSW INF: CPSW3G found. CPSW INF: HW-Id: 0x0019, RTL: 0, Major: 1, Minor: 0xc
001154 : CPSW INF: PHY found. Id=0x2000a211
001154 : CPSW INF: Restart PHY auto negotiation
007214 : CPSW INF: PHY link timeout (waiting for auto negotiation completion).
007232 : Unlicensed version, stop sending ethernet frames after 60 minutes!
007234 : Ethernet cable not connected
007243 : ecatScanBus() Error 0x9811002d in McSm state 'SB_DONE' for requested state 'SB_DONE'
007243 : Cannot scan bus: ERROR: Ethernet link cable disconnected (0x9811002d)
007243 : EtherCAT network adapter MAC: 68-C9-0B-1C-83-22
Yaoming Qin：
回复 tao zhang16:
主站的网口是不是不对？
