调用HalCoGen生成的EEPROM驱动，编译出错。。。。

  问个关于调用F021函数库的问题，我在HalcoGen上配置了CAN和FEE驱动，移植到CCS6.2新建工程中，现在可以实现CAN的收发，但是在新建一个HSI_EEPROM.c文件中引用头文件,后调用ti_fee.h。然后再主函数中调用函数hsi_eeprom_init();

编译器报错：

F021.h是重复包含了么？

David Bai1：

Hi Xuehui,

建议按HALCoGen->Help->Help Topics里的例程介绍进行操作：

example_TI_Fee_Write_Read.c

This is an example which descibes the steps to use TI-Fee Driver for simple Write Sync, Write Async, Read, Invalidate and Full Format of EEPROM bank.

Step 1:

Create a new project.

Navigate: -> File -> New -> Project -> TMS570xx / RMx

Step 2:

Configure driver code generation:

Enable TI-FEE driver
Disable others

Navigate: -> TMS570xx / RMx -> Driver Enable

Step 3:

Navigate: -> TMS570xx / RMx -> TI-FEE

Configure FEE settings ( Leave Default for below Example)

Step 4:

Navigate: -> File -> Generate Code

Step 5:

Copy source code below into your application.

Step 6:

Add F021 Library files to CCS Project

Add/Link F021_API_CortexR4_BE_V3D16.lib from folder C:/ti/Hercules/F021 Flash API/2.01.01 to CCS Project
Add Path C:/ti/Hercules/F021 Flash API/2.01.01/include to Include Path in CCS Project

The example file example_TI_Fee_Write_Read.c can also be found in the examples folder: ../HALCoGen/examples

NoteHALCoGen generates an enpty main function in sys_main.c, please make sure that you link in the right main function or copy the source into the user code sections of this file.

/* (c) Texas Instruments 2009-2015, All rights reserved. *//*
* Copyright (C) 2009-2015 Texas Instruments Incorporated - www.ti.com
*
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
*
* Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the
* distribution.
*
* Neither the name of Texas Instruments Incorporated nor the names of
* its contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
* OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
* SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT
* LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
*//* USER CODE BEGIN (0) */
#include "ti_fee.h"
/* USER CODE END *//* Include Files */
#include "sys_common.h"
/* USER CODE BEGIN (1) */uint16 u16JobResult,Status;
Std_ReturnType oResult=E_OK;
unsigned char read_data[100]={0};uint8 SpecialRamBlock[100];unsigned char pattern;
uint16 u16writecounter;unsigned int FeeVirtualSectorNumber;
unsigned char VsState, u8EEPIndex;
unsigned char u8VirtualSector;
uint8 Test_Recovery;
uint8 Test_Cancel;void delay(void)
{
unsigned int dummycnt=0x0000FFU;
do
{
dummycnt--;
}
while(dummycnt>0);
}
/* USER CODE END *//* USER CODE BEGIN (2) */
/* USER CODE END */void main(void)
{
/* USER CODE BEGIN (3) */
unsigned int BlockNumber;
unsigned int BlockOffset, Length;
unsigned char *Read_Ptr=read_data;unsigned int loop;/* Initialize RAM array.*/
for(loop=0;loop<100;loop++)SpecialRamBlock[loop] = loop;/* Initialize FEE. This will create Virtual sectors, initialize global variables etc.*/
TI_Fee_Init();
do
{
TI_Fee_MainFunction();
delay();
Status=TI_Fee_GetStatus(0 );
}
while(Status!= IDLE);/* Write the block into EEP Asynchronously. Block size is configured in ti_fee_cfg.c file. Default Block size is
8 bytes */
BlockNumber=0x1;
TI_Fee_WriteAsync(BlockNumber, &SpecialRamBlock[0]);
do
{
TI_Fee_MainFunction();
delay();
Status=TI_Fee_GetStatus(0);
}
while(Status!=IDLE);/* Write the block into EEP Synchronously. Write will not happen since data is same. */
TI_Fee_WriteSync(BlockNumber, &SpecialRamBlock[0]);/* Read the block with unknown length */
BlockOffset = 0;
Length = 0xFFFF;
oResult=TI_Fee_Read(BlockNumber,BlockOffset,Read_Ptr,Length);
do
{
TI_Fee_MainFunction();
delay();
Status=TI_Fee_GetStatus(0);
}
while(Status!=IDLE);/* Invalidate a written block */
TI_Fee_InvalidateBlock(BlockNumber);
do
{
TI_Fee_MainFunction();
delay();
Status=TI_Fee_GetStatus(0);
}
while(Status!=IDLE);/* Format bank 7 */
TI_Fee_Format(0xA5A5A5A5U);while(1);
/* USER CODE END */
}/* USER CODE BEGIN (4) */
/* USER CODE END */

David Bai1：

Hi Xuehui,

在按上述步骤配置完后，在新建main()文件时，需注意将HALCoGen自动生成的空的main()文件删除，避免重复。

Xuehui Wang1：

回复 David Bai1:

Hi David ：

  根据例子我把编写以下几个函数：

void hsi_feeInit(void){ /* Initialize FEE. This will create Virtual sectors, initialize global variables etc.*/ TI_Fee_Init(); do { TI_Fee_MainFunction(); delay_time(); Status=TI_Fee_GetStatus(0 ); } while(Status!= IDLE); 
}
void hsi_feeWrite(uint8_t BlockNumber , uint8_t *SpecialRamBlock){/* Write the block into EEP Asynchronously. Block size is configured in ti_fee_cfg.c file. Default Block size is 8 bytes */
 TI_Fee_WriteSync(BlockNumber, SpecialRamBlock); do {  TI_Fee_MainFunction();  delay_time();  Status=TI_Fee_GetStatus(0); } while(Status!=IDLE);}void hsi_feeRead(uint8_t BlockNumber , uint8_t BlockOffset ,uint8_t *SpecialRamBlock , uint8_t Length){ /* Read the block with unknown length */
 oResult=TI_Fee_Read(BlockNumber,BlockOffset,SpecialRamBlock,Length); do {  TI_Fee_MainFunction();  delay_time();  Status=TI_Fee_GetStatus(0); } while(Status!=IDLE);}
void hsi_feeFormat(void){  TI_Fee_Format(0xA5A5A5A5U);}

调用初始化函数后怎么EEPROM会有错误的数据，刷写代码的的时候已经把EEPROM擦除了，应该都是FF。调用初始化函数后EEPROM如下图：

调用写入数据函数数据也不对。
能帮忙修改一下读写例程么 ？

Xuehui Wang1：

回复 David Bai1:

Hi  David：

  编译的问题已经解决了。 对于EEPROM的操作我直接使用F021的函数可以操作，用了HalCoGen生成的驱动调用有点问题。