求助TM4C1294的LED灯点亮问题

这是所写代码

void main(void)

{

SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
GPIODirModeSet(GPIO_PORTF_BASE,GPIO_PIN_1,GPIO_DIR_MODE_OUT);
GPIOPadConfigSet(GPIO_PORTF_BASE,GPIO_PIN_1,GPIO_STRENGTH_8MA_SC,GPIO_PIN_TYPE_STD);
GPIOPinWrite(GPIO_PORTF_BASE,GPIO_PIN_1,0xff);
while(1)
{};
}

编译后显示

CORTEX_M4_0: GEL Output:Memory Map Initialization Complete

但板子上LED灯D1，D2，D3不亮

xyz549040622：

GPIOPinWrite的第三个参数写入不正确。你的系统时钟的设置在哪呢？

user5298952：

回复 xyz549040622:

第三个参数修改后，加入系统时钟，LED灯仍不亮

user5298952：

回复 user5298952:

#include <stdint.h>
#include <stdbool.h>
#include "inc/hw_ints.h"
#include "inc/hw_memmap.h"
#include "inc/hw_nvic.h"
#include "inc/hw_types.h"
#include "driverlib/gpio.h"
#include "driverlib/interrupt.h"
#include "driverlib/pin_map.h"
#include "driverlib/systick.h"
#include "driverlib/sysctl.h"
#include "driverlib/timer.h"
#include "utils/uartstdio.h"

void main(void)
{
SysCtlPeripheralEnable (SYSCTL_PERIPH_GPIOF);GPIODirModeSet(GPIO_PORTF_BASE,GPIO_PIN_1,GPIO_DIR_MODE_OUT);GPIOPadConfigSet(GPIO_PORTF_BASE,GPIO_PIN_1,GPIO_STRENGTH_8MA_SC,GPIO_PIN_TYPE_STD);GPIOPinWrite(GPIO_PORTF_BASE,GPIO_PIN_1,GPIO_PIN_1);while(1){};
}

xyz549040622：

回复 user5298952:

没看到你主时钟的设置在哪，给你一个LED闪烁的例程

//*****************************************************************************
//
// project0.c - Example to demonstrate minimal TivaWare setup
//
// Copyright (c) 2012-2017 Texas Instruments Incorporated.All rights reserved.
// Software License Agreement
//// Texas Instruments (TI) is supplying this software for use solely and
// exclusively on TI's microcontroller products. The software is owned by
// TI and/or its suppliers, and is protected under applicable copyright
// laws. You may not combine this software with "viral" open-source
// software in order to form a larger program.
//// THIS SOFTWARE IS PROVIDED "AS IS" AND WITH ALL FAULTS.
// NO WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT
// NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
// A PARTICULAR PURPOSE APPLY TO THIS SOFTWARE. TI SHALL NOT, UNDER ANY
// CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
// DAMAGES, FOR ANY REASON WHATSOEVER.
//// This is part of revision 2.1.4.178 of the EK-TM4C1294XL Firmware Package.
//
//*****************************************************************************#include <stdint.h>
#include <stdbool.h>
#include "inc/hw_types.h"
#include "inc/hw_memmap.h"
#include "driverlib/sysctl.h"
#include "driverlib/gpio.h"//*****************************************************************************
//
// Define pin to LED mapping.
//
//*****************************************************************************//*****************************************************************************
//
//! \addtogroup example_list
//! <h1>Project Zero (project0)</h1>
//!
//! This example demonstrates the use of TivaWare to setup the clocks and
//! toggle GPIO pins to make the LED blink. This is a good place to start
//! understanding your launchpad and the tools that can be used to program it.
//
//*****************************************************************************#define USER_LED1GPIO_PIN_0
#define USER_LED2GPIO_PIN_1//*****************************************************************************
//
// The error routine that is called if the driver library encounters an error.
//
//*****************************************************************************
#ifdef DEBUG
void
__error__(char *pcFilename, uint32_t ui32Line)
{
}
#endif//*****************************************************************************
//
// Main 'C' Language entry point.Toggle an LED using TivaWare.
//
//*****************************************************************************
int
main(void)
{uint32_t ui32SysClock;//// Run from the PLL at 120 MHz.//ui32SysClock = SysCtlClockFreqSet((SYSCTL_XTAL_25MHZ |SYSCTL_OSC_MAIN |SYSCTL_USE_PLL |SYSCTL_CFG_VCO_480), 120000000);//// Enable and wait for the port to be ready for access//SysCtlPeripheralEnable(SYSCTL_PERIPH_GPION);while(!SysCtlPeripheralReady(SYSCTL_PERIPH_GPION)){}//// Configure the GPIO port for the LED operation.//GPIOPinTypeGPIOOutput(GPIO_PORTN_BASE, (USER_LED1|USER_LED2));//// Loop Forever//while(1){//// Turn on the LED//GPIOPinWrite(GPIO_PORTN_BASE, (USER_LED1|USER_LED2), USER_LED1);//// Delay for a bit//SysCtlDelay(ui32SysClock/6);//// Turn on the LED//GPIOPinWrite(GPIO_PORTN_BASE, (USER_LED1|USER_LED2), USER_LED2);//// Delay for a bit//SysCtlDelay(ui32SysClock/6);}
}