CC1310: CC1310射频开启发射到结束所需时间

Hi team, I am using the CC1310 RTOS this code is in a while(1),I found that it's consuming time is about 180ms(approxiately),is the consuming time in this while(1) correct 50kbps rfpacketTX？and then I noticed that the current also seems to be relatively high than CC1310 datasheet explained.

/* 待机定时10秒 */sleepTickCount = 1000000 / Clock_tickPeriod;//UART_write(uart,&by, 1);while(1){ledPinHandle = PIN_open(&ledPinState, pinTable);// IOCPinTypeGpioOutput(0x1);ADC_init();ADC_Handleadc;ADC_Paramsparams;int_fast16_t res;ADC_Params_init(&params);adc = ADC_open(CC1310_LAUNCHXL_ADC7 , &params);if (adc == NULL){while (1);}/* Blocking mode conversion */res = ADC_convert(adc, &adcValue0);packet[4]=adcValue0  & 0xFF;packet[5]=adcValue0;if (res == ADC_STATUS_SUCCESS) {adcValue0MicroVolt = ADC_convertRawToMicroVolts(adc, adcValue0);packet[0] =(adcValue0MicroVolt >> 24) & 0xFF;  // 获取高8位packet[1] =(adcValue0MicroVolt >> 16) & 0xFF;  // 获取次高8位packet[2]= (adcValue0MicroVolt >> 8) & 0xFF;// 获取次低8位packet[3] = adcValue0MicroVolt & 0xFF;//  UART_write(uart,&byte, 4);double X= (double)adcValue0MicroVolt; // 将 adcValue0MicroVolt 转换为 double 类型的变量 numberuint16_t integer_part;calculate_R(X, &integer_part);
 double ln_R = log(integer_part); // 计算ln(R)
 double result=3950/(ln_R+4.038);
 result= result-273.15;
uint8_t xx=(uint8_t)result;//取整double erWithTwoDecimals = result * 100; // 将原始数乘以 100，以保留两位小数uint16_t xy = (uint16_t)erWithTwoDecimals;uint8_t de = xy % 100;packet[4]=xx;packet[5]=de;packet[6]=1;//sprintf("%d",packet[6]);packet[7]=1;//UART_write(uart,&packet, 8);//sprintf(byte[0],"%d",30);//UART_write(uart,&byte, 1);//sprintf(ascii_array[0],"%d",packet[6]);//UART_write(uart,&ascii_array, 1);}//Task_sleep(sleepTickCount);ADC_close(adc);
PIN_close(ledPinHandle);
 ledPinHandle = PIN_open(&ledPinState, shutTable);//PIN_setOutputValue(ledPinHandle, CC1310_LAUNCHXL_PIN_RLED , !PIN_getOutputValue(CC1310_LAUNCHXL_PIN_RLED ));//usleep(10000);//PIN_setOutputValue(ledPinHandle, CC1310_LAUNCHXL_PIN_RLED , !PIN_getOutputValue(CC1310_LAUNCHXL_PIN_RLED ));//UART_write(uart, &input, 2);//AONBatMonDisable ();/* Request access to the radio */#if defined(DeviceFamily_CC26X0R2)rfHandle = RF_open(&rfObject, &RF_prop, (RF_RadioSetup*)&RF_cmdPropRadioSetup, &rfParams);#elserfHandle = RF_open(&rfObject, &RF_prop, (RF_RadioSetup*)&RF_cmdPropRadioDivSetup, &rfParams);#endif// DeviceFamily_CC26X0R2// RF_cmdPropRadioDivSetup.txPower=0x913F;//设置频率RF_CmdHandle txTestHnle=RF_postCmd(rfHandle, (RF_Op*)&RF_cmdFs, RF_PriorityNormal, NULL, 0);/* Create packet with incrementing sequence number and random payload */
//packet[0] = input[0];uint8_t i;for (i = 7; i < PAYLOAD_LENGTH; i++){packet[i] = 1;}xor_encrypt_decrypt(packet, key, PAYLOAD_LENGTH);/* Send packet */RF_EventMask terminationReason = RF_runCmd(rfHandle, (RF_Op*)&RF_cmdPropTx,RF_PriorityNormal, NULL, 0);//stuck on this step//  switch(terminationReason)//  {//case RF_EventLastCmdDone://// A stand-alone radio operation command or the last radio//// operation command in a chain finished.//break;//case RF_EventCmdCancelled://// Command cancelled before it was started; it can be caused//// by RF_cancelCmd() or RF_flushCmd().//break;//case RF_EventCmdAborted://// Abrupt command termination caused by RF_cancelCmd() or//// RF_flushCmd().//break;//case RF_EventCmdStopped://// Graceful command termination caused by RF_cancelCmd() or//// RF_flushCmd().//break;//default://// Uncaught error event//while(1);//  }////  uint32_t cmdStatus = ((volatile RF_Op*)&RF_cmdPropTx)->status;//  switch(cmdStatus)//  {//case PROP_DONE_OK://// 传输包成功//break;//case PROP_DONE_STOPPED://// received CMD_STOP while transmitting packet and finished//// transmitting packet//break;//case PROP_DONE_ABORT://// Received CMD_ABORT while transmitting packet//break;//case PROP_ERROR_PAR://// Observed illegal parameter//break;//case PROP_ERROR_NO_SETUP://// Command sent without setting up the radio in a supported//// mode using CMD_PROP_RADIO_SETUP or CMD_RADIO_SETUP//break;//case PROP_ERROR_NO_FS://// Command sent without the synthesizer being programmed//break;//case PROP_ERROR_TXUNF://// TX underflow observed during operation//break;//default://// Uncaught error event - these could come from the//// pool of states defined in rf_mailbox.h//while(1);//  }#ifndef POWER_MEASUREMENT//PIN_setOutputValue(ledPinHandle, Board_PIN_LED1,!PIN_getOutputValue(Board_PIN_LED1));#endif/* Power down the radio */RF_yield(rfHandle);#ifdef POWER_MEASUREMENT/* Sleep for PACKET_INTERVAL s */sleep(PACKET_INTERVAL);#else/* Sleep for PACKET_INTERVAL us */usleep(PACKET_INTERVAL);#endifRF_cancelCmd(rfHandle,txTestHnle,0);//RF_flushCmd (rfHandle,txTestHnle,1);//擦除RF_yield(rfHandle);//断电RF_close(rfHandle);PIN_close(ledPinHandle);Task_sleep(sleepTickCount);}

Links：

感谢您对TI产品的关注！为更加有效地解决您的问题，我们建议您将问题发布在E2E英文技术论坛上（e2e.ti.com/…/addpost