TI中文支持网Part Number:C2000-GANG
烧录两个设备，单独烧录都没问题，但不能两个同时烧录，两个同时连接好只能烧录其中一个，另一个上位机显示未连接，根据产品介绍是可以多设备同时烧录的。
Ben Qin：
你好，C2000-gang最多支持8台设备同时烧录。
首先请确保你使用的是最新的软件包：
content.elprotronic.ca/C2000-GANG-Setup.zip
然后参考下user guide：
C2000 Gang Programmer (C2000-GANG) (Rev. C) (ti.com.cn)
,
? ?：
目前是驱动板上有两个同型号的dsp芯片，两者供电和GND是连通的，烧录同样的程序，现在烧录不能实现同时烧录且很不稳定，有时可以烧录有时不行，能否指导具体如何接线及上位机配置，用户手册看了也未解决，想知道这种情况是两个芯片都单独连接烧录器一路还是两路信号线串联起来，另外看手册上连接烧录器电源那Vext引脚应该有3.3V输出电压，但经测量并没有电压输出，请问这是正常的吗。贵公司有无技术支持可以电话沟通指导，谢谢。
,
? ?：
这是自检报告，连线前无错误，接线后报错，芯片3.3V接到烧录器vext引脚，芯片也有单独供电，两芯片TMS、TDI、TDO、TCK、TRST引脚均单独接到烧录器两路的各自引脚，芯片GND与烧录器GND未连接，（另外试过GND相连，也一样无效，也试过芯片不单独供电，上位机报错VCC低）
=== C2000-GANG Self test results ( Saturday, April 22, 2023, 11:27:27 ) ===
Adapter SN ——: 21111617 Hardware ——–: C2K : 01.05Access key ——: C2000 – Gang Programmer Silicon Number –: 12F0 5B51 2700 0700API Firmware —-: C2K-Gang AC28: 01.01.09.00BOOT Firmware —: G430BOOT B430: 01.00.02.00GUI Software —-: C2000-Gang-GUI G28x: 01.01.09.00DLL Software —-: C2000-Gang-DLL D280: 01.01.09.00
================ Test results =============
No. name parameter limits result status
1: Data Bus (ALL LOW) 0x0000 (0x0000 – 0x0000) Result: 0x00 … >> OK << 2: Data Bus (ALL HIGH) 0x00FF (0xFFFF – 0xFFFF) Result: 0xFFFF … >> OK << 3: Data Bus (D-0 HI ) 0x0001 (0x0101 – 0x0101) Result: 0x0101 … >> OK << 4: Data Bus (D-1 HI ) 0x0002 (0x0202 – 0x0202) Result: 0x0202 … >> OK << 5: Data Bus (D-2 HI ) 0x0004 (0x0404 – 0x0404) Result: 0x0404 … >> OK << 6: Data Bus (D-3 HI ) 0x0008 (0x0808 – 0x0808) Result: 0x0808 … >> OK << 7: Data Bus (D-4 HI ) 0x0010 (0x1010 – 0x1010) Result: 0x1010 … >> OK << 8: Data Bus (D-5 HI ) 0x0020 (0x2020 – 0x2020) Result: 0x2020 … >> OK << 9: Data Bus (D-6 HI ) 0x0040 (0x4040 – 0x4040) Result: 0x4040 … >> OK << 10: Data Bus (D-7 HI ) 0x0080 (0x8080 – 0x8080) Result: 0x8080 … >> OK <<
11: Data-2 Bus (ALL LOW) 0x0000 (0x0000 – 0x0000) Result: 0x00 … >> OK << 12: Data-2 Bus (ALL HIGH) 0x00FF (0xFFFF – 0xFFFF) Result: 0xFFFF … >> OK << 13: Data-2 Bus (D2-0 HI ) 0x0001 (0x0101 – 0x0101) Result: 0x0101 … >> OK << 14: Data-2 Bus (D2-1 HI ) 0x0002 (0x0202 – 0x0202) Result: 0x0202 … >> OK << 15: Data-2 Bus (D2-2 HI ) 0x0004 (0x0404 – 0x0404) Result: 0x0404 … >> OK << 16: Data-2 Bus (D2-3 HI ) 0x0008 (0x0808 – 0x0808) Result: 0x0808 … >> OK << 17: Data-2 Bus (D2-4 HI ) 0x0010 (0x1010 – 0x1010) Result: 0x1010 … >> OK << 18: Data-2 Bus (D2-5 HI ) 0x0020 (0x2020 – 0x2020) Result: 0x2020 … >> OK << 19: Data-2 Bus (D2-6 HI ) 0x0040 (0x4040 – 0x4040) Result: 0x4040 … >> OK << 20: Data-2 Bus (D2-7 HI ) 0x0080 (0x8080 – 0x8080) Result: 0x8080 … >> OK <<
21: Vcc Target-1 (ALL OFF) 0.00 V ( 0.00 to 0.30) Result: 0.02 V … >> OK << 22: Vcc Target-2 (ALL OFF) 0.00 V ( 0.00 to 0.30) Result: 0.01 V … >> OK << 23: Vcc Target-3 (ALL OFF) 0.00 V ( 0.00 to 0.30) Result: 0.01 V … >> OK << 24: Vcc Target-4 (ALL OFF) 0.00 V ( 0.00 to 0.30) Result: 0.01 V … >> OK << 25: Vcc Target-5 (ALL OFF) 0.00 V ( 0.00 to 0.30) Result: 0.01 V … >> OK << 26: Vcc Target-6 (ALL OFF) 0.00 V ( 0.00 to 0.30) Result: 0.01 V … >> OK << 27: Vcc Target-7 (ALL OFF) 0.00 V ( 0.00 to 0.30) Result: 2.42 V … >> ERROR << 28: Vcc Target-8 (ALL OFF) 0.00 V ( 0.00 to 0.30) Result: 0.02 V … >> OK <<
29: Translators VT (OFF) 0.00 V ( 0.00 to 0.50) Result: 0.02 V … >> OK << 30: Translators VT (ON 3.3V) 3.30 V ( 3.10 to 3.50) Result: 3.29 V … >> OK <<
31: Vpp Voltage-in 10.00 V ( 8.00 to 12.00) Result: 10.43 V … >> OK << 32: Vpp Voltage 7.00 V ( 6.50 to 7.30) Result: 6.87 V … >> OK << 33: Internal Vcc-3.3V 3.30 V ( 3.20 to 3.40) Result: 3.30 V … >> OK <<
34: Vcc Target-1 (ALL ON 3.3V) 3.30 V ( 3.10 to 3.50) Result: 3.29 V … >> OK << 35: Vcc Target-2 (ALL ON 3.3V) 3.30 V ( 3.10 to 3.50) Result: 3.30 V … >> OK << 36: Vcc Target-3 (ALL ON 3.3V) 3.30 V ( 3.10 to 3.50) Result: 3.30 V … >> OK << 37: Vcc Target-4 (ALL ON 3.3V) 3.30 V ( 3.10 to 3.50) Result: 3.33 V … >> OK << 38: Vcc Target-5 (ALL ON 3.3V) 3.30 V ( 3.10 to 3.50) Result: 3.31 V … >> OK << 39: Vcc Target-6 (ALL ON 3.3V) 3.30 V ( 3.10 to 3.50) Result: 3.33 V … >> OK << 40: Vcc Target-7 (ALL ON 3.3V) 3.30 V ( 3.10 to 3.50) Result: 3.30 V … >> OK << 41: Vcc Target-8 (ALL ON 3.3V) 3.30 V ( 3.10 to 3.50) Result: 3.32 V … >> OK <<
42: Vcc discharge (250ms)Target-1 3.30 V ( 0.30 to 1.50) Result: 0.79 V … >> OK << 43: Vcc discharge (250ms)Target-2 3.30 V ( 0.30 to 1.50) Result: 0.79 V … >> OK << 44: Vcc discharge (250ms)Target-3 3.30 V ( 0.30 to 1.50) Result: 0.78 V … >> OK << 45: Vcc discharge (250ms)Target-4 3.30 V ( 0.30 to 1.50) Result: 0.79 V … >> OK << 46: Vcc discharge (250ms)Target-5 3.30 V ( 0.30 to 1.50) Result: 0.79 V … >> OK << 47: Vcc discharge (250ms)Target-6 3.30 V ( 0.30 to 1.50) Result: 0.78 V … >> OK << 48: Vcc discharge (250ms)Target-7 3.30 V ( 0.30 to 1.50) Result: 2.44 V … >> ERROR << 49: Vcc discharge (250ms)Target-8 3.30 V ( 0.30 to 1.50) Result: 0.79 V … >> OK <<
50: Vcc Target-1 ( #1 ON ) 0.00 V ( 3.10 to 3.50) Result: 3.29 V … >> OK << 51: Vcc Target-2 ( #1 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 52: Vcc Target-3 ( #1 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 53: Vcc Target-4 ( #1 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 54: Vcc Target-5 ( #1 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 55: Vcc Target-6 ( #1 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.15 V … >> OK << 56: Vcc Target-7 ( #1 ON ) 0.00 V ( 0.00 to 0.50) Result: 2.44 V … >> ERROR << 57: Vcc Target-8 ( #1 ON ) 3.30 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 58: Vcc Target-1 ( #2 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 59: Vcc Target-2 ( #2 ON ) 0.00 V ( 3.10 to 3.50) Result: 3.30 V … >> OK << 60: Vcc Target-3 ( #2 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 61: Vcc Target-4 ( #2 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 62: Vcc Target-5 ( #2 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 63: Vcc Target-6 ( #2 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.15 V … >> OK << 64: Vcc Target-7 ( #2 ON ) 0.00 V ( 0.00 to 0.50) Result: 2.44 V … >> ERROR << 65: Vcc Target-8 ( #2 ON ) 3.30 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 66: Vcc Target-1 ( #3 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 67: Vcc Target-2 ( #3 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 68: Vcc Target-3 ( #3 ON ) 0.00 V ( 3.10 to 3.50) Result: 3.29 V … >> OK << 69: Vcc Target-4 ( #3 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 70: Vcc Target-5 ( #3 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 71: Vcc Target-6 ( #3 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.15 V … >> OK << 72: Vcc Target-7 ( #3 ON ) 0.00 V ( 0.00 to 0.50) Result: 2.44 V … >> ERROR << 73: Vcc Target-8 ( #3 ON ) 3.30 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 74: Vcc Target-1 ( #4 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 75: Vcc Target-2 ( #4 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 76: Vcc Target-3 ( #4 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 77: Vcc Target-4 ( #4 ON ) 0.00 V ( 3.10 to 3.50) Result: 3.33 V … >> OK << 78: Vcc Target-5 ( #4 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 79: Vcc Target-6 ( #4 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.15 V … >> OK << 80: Vcc Target-7 ( #4 ON ) 0.00 V ( 0.00 to 0.50) Result: 2.44 V … >> ERROR << 81: Vcc Target-8 ( #4 ON ) 3.30 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 82: Vcc Target-1 ( #5 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 83: Vcc Target-2 ( #5 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 84: Vcc Target-3 ( #5 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 85: Vcc Target-4 ( #5 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 86: Vcc Target-5 ( #5 ON ) 0.00 V ( 3.10 to 3.50) Result: 3.31 V … >> OK << 87: Vcc Target-6 ( #5 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 88: Vcc Target-7 ( #5 ON ) 0.00 V ( 0.00 to 0.50) Result: 2.44 V … >> ERROR << 89: Vcc Target-8 ( #5 ON ) 3.30 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 90: Vcc Target-1 ( #6 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 91: Vcc Target-2 ( #6 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 92: Vcc Target-3 ( #6 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 93: Vcc Target-4 ( #6 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 94: Vcc Target-5 ( #6 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 95: Vcc Target-6 ( #6 ON ) 0.00 V ( 3.10 to 3.50) Result: 3.33 V … >> OK << 96: Vcc Target-7 ( #6 ON ) 0.00 V ( 0.00 to 0.50) Result: 2.44 V … >> ERROR << 97: Vcc Target-8 ( #6 ON ) 3.30 V ( 0.00 to 0.50) Result: 0.16 V … >> OK << 98: Vcc Target-1 ( #7 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK << 99: Vcc Target-2 ( #7 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK <<100: Vcc Target-3 ( #7 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK <<101: Vcc Target-4 ( #7 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK <<102: Vcc Target-5 ( #7 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK <<103: Vcc Target-6 ( #7 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK <<104: Vcc Target-7 ( #7 ON ) 0.00 V ( 3.10 to 3.50) Result: 3.29 V … >> OK <<105: Vcc Target-8 ( #7 ON ) 3.30 V ( 0.00 to 0.50) Result: 0.16 V … >> OK <<106: Vcc Target-1 ( #8 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.17 V … >> OK <<107: Vcc Target-2 ( #8 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK <<108: Vcc Target-3 ( #8 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK <<109: Vcc Target-4 ( #8 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK <<110: Vcc Target-5 ( #8 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.16 V … >> OK <<111: Vcc Target-6 ( #8 ON ) 0.00 V ( 0.00 to 0.50) Result: 0.15 V … >> OK <<112: Vcc Target-7 ( #8 ON ) 0.00 V ( 0.00 to 0.50) Result: 2.44 V … >> ERROR <<113: Vcc Target-8 ( #8 ON ) 3.30 V ( 3.10 to 3.50) Result: 3.32 V … >> OK <<
114: SD Power OFF 0x0000 (0x0000 – 0x0000) Result: 0x00 … >> OK <<115: SD Power ON 0x0001 (0x0001 – 0x0001) Result: 0x01 … >> OK <<116: SD Discharge – delay 2ms 0x0010 (0x0001 – 0x0001) Result: 0x01 … >> OK <<117: SD Discharge – delay 50ms 0x0010 (0x0000 – 0x0000) Result: 0x00 … >> OK <<
118: BSL RX bus (#1 HIGH) 0x0001 (0x0001 – 0x0001) Result: 0x01 … >> OK <<119: BSL RX bus (#2 HIGH) 0x0002 (0x0002 – 0x0002) Result: 0x02 … >> OK <<120: BSL RX bus (#3 HIGH) 0x0004 (0x0004 – 0x0004) Result: 0x04 … >> OK <<121: BSL RX bus (#4 HIGH) 0x0008 (0x0008 – 0x0008) Result: 0x08 … >> OK <<122: BSL RX bus (#5 HIGH) 0x0010 (0x0010 – 0x0010) Result: 0x10 … >> OK <<123: BSL RX bus (#6 HIGH) 0x0020 (0x0020 – 0x0020) Result: 0x20 … >> OK <<124: BSL RX bus (#7 HIGH) 0x0040 (0x0040 – 0x0040) Result: 0x40 … >> OK <<125: BSL RX bus (#8 HIGH) 0x0080 (0x0080 – 0x0080) Result: 0x80 … >> OK <<
126: BSL TX bus (#1 HIGH) 0x0001 (0x0001 – 0x0001) Result: 0x01 … >> OK <<127: BSL TX bus (#2 HIGH) 0x0002 (0x0002 – 0x0002) Result: 0x02 … >> OK <<128: BSL TX bus (#3 HIGH) 0x0004 (0x0004 – 0x0004) Result: 0x04 … >> OK <<129: BSL TX bus (#4 HIGH) 0x0008 (0x0008 – 0x0008) Result: 0x08 … >> OK <<130: BSL TX bus (#5 HIGH) 0x0010 (0x0010 – 0x0010) Result: 0x10 … >> OK <<131: BSL TX bus (#6 HIGH) 0x0020 (0x0020 – 0x0020) Result: 0x20 … >> OK <<132: BSL TX bus (#7 HIGH) 0x0040 (0x0040 – 0x0040) Result: 0x40 … >> OK <<133: BSL TX bus (#8 HIGH) 0x0080 (0x0080 – 0x0080) Result: 0x80 … >> OK <<
134: TDI bus (#8 HIGH) 0x0080 (0x0080 – 0x0080) Result: 0xC4 … >> ERROR <<135: TDI bus (#1 HIGH) 0x0001 (0x0001 – 0x0001) Result: 0x45 … >> ERROR <<136: TDI bus (#2 HIGH) 0x0002 (0x0002 – 0x0002) Result: 0x46 … >> ERROR <<137: TDI bus (#3 HIGH) 0x0004 (0x0004 – 0x0004) Result: 0x44 … >> ERROR <<138: TDI bus (#4 HIGH) 0x0008 (0x0008 – 0x0008) Result: 0x4C … >> ERROR <<139: TDI bus (#5 HIGH) 0x0010 (0x0010 – 0x0010) Result: 0x54 … >> ERROR <<140: TDI bus (#6 HIGH) 0x0020 (0x0020 – 0x0020) Result: 0x64 … >> ERROR <<141: TDI bus (#7 HIGH) 0x0040 (0x0040 – 0x0040) Result: 0x44 … >> ERROR <<
142: TDIO Tx-bus (#1 HIGH) 0x0001 (0x0001 – 0x0001) Result: 0x45 … >> ERROR <<143: TDIO Tx-bus (#2 HIGH) 0x0002 (0x0002 – 0x0002) Result: 0x46 … >> ERROR <<144: TDIO Tx-bus (#3 HIGH) 0x0004 (0x0004 – 0x0004) Result: 0x44 … >> ERROR <<145: TDIO Tx-bus (#4 HIGH) 0x0008 (0x0008 – 0x0008) Result: 0x4C … >> ERROR <<146: TDIO Tx-bus (#5 HIGH) 0x0010 (0x0010 – 0x0010) Result: 0x54 … >> ERROR <<147: TDIO Tx-bus (#6 HIGH) 0x0020 (0x0020 – 0x0020) Result: 0x64 … >> ERROR <<148: TDIO Tx-bus (#7 HIGH) 0x0040 (0x0040 – 0x0040) Result: 0x44 … >> ERROR <<149: TDIO Tx-bus (#8 HIGH) 0x0080 (0x0080 – 0x0080) Result: 0xC4 … >> ERROR <<
150: TDIO Tx-Rx (#1 HIGH) 0x0001 (0x0001 – 0x0001) Result: 0x01 … >> OK <<151: TDIO Tx-Rx (#2 HIGH) 0x0002 (0x0002 – 0x0002) Result: 0x02 … >> OK <<152: TDIO Tx-Rx (#3 HIGH) 0x0004 (0x0004 – 0x0004) Result: 0x04 … >> OK <<153: TDIO Tx-Rx (#4 HIGH) 0x0008 (0x0008 – 0x0008) Result: 0x08 … >> OK <<154: TDIO Tx-Rx (#5 HIGH) 0x0010 (0x0010 – 0x0010) Result: 0x10 … >> OK <<155: TDIO Tx-Rx (#6 HIGH) 0x0020 (0x0020 – 0x0020) Result: 0x20 … >> OK <<156: TDIO Tx-Rx (#7 HIGH) 0x0040 (0x0040 – 0x0040) Result: 0x40 … >> OK <<157: TDIO Tx-Rx (#8 HIGH) 0x0080 (0x0080 – 0x0080) Result: 0x80 … >> OK <<
158: TDIO Rx-bus (#1 HIGH) 0x0001 (0x0001 – 0x0001) Result: 0x45 … >> ERROR <<159: TDIO Rx-bus (#2 HIGH) 0x0002 (0x0002 – 0x0002) Result: 0x46 … >> ERROR <<160: TDIO Rx-bus (#3 HIGH) 0x0004 (0x0004 – 0x0004) Result: 0x44 … >> ERROR <<161: TDIO Rx-bus (#4 HIGH) 0x0008 (0x0008 – 0x0008) Result: 0x4C … >> ERROR <<162: TDIO Rx-bus (#5 HIGH) 0x0010 (0x0010 – 0x0010) Result: 0x54 … >> ERROR <<163: TDIO Rx-bus (#6 HIGH) 0x0020 (0x0020 – 0x0020) Result: 0x64 … >> ERROR <<164: TDIO Rx-bus (#7 HIGH) 0x0040 (0x0040 – 0x0040) Result: 0x44 … >> ERROR <<165: TDIO Rx-bus (#84 HIGH) 0x0080 (0x0080 – 0x0080) Result: 0xC4 … >> ERROR <<
166: TMS bus (All HIGH) 0x00FF (0x00FF – 0x00FF) Result: 0xFF … >> OK <<167: TMS bus (All LOW) 0x0000 (0x0000 – 0x0000) Result: 0x00 … >> OK <<
168: TMS bus (#1 HIGH) 0x0001 (0x0001 – 0x0001) Result: 0x41 … >> ERROR <<169: TMS bus (#2 HIGH) 0x0002 (0x0002 – 0x0002) Result: 0x42 … >> ERROR <<170: TMS bus (#3 HIGH) 0x0004 (0x0004 – 0x0004) Result: 0x04 … >> OK <<171: TMS bus (#4 HIGH) 0x0008 (0x0008 – 0x0008) Result: 0x08 … >> OK <<172: TMS bus (#5 HIGH) 0x0010 (0x0010 – 0x0010) Result: 0x10 … >> OK <<173: TMS bus (#6 HIGH) 0x0020 (0x0020 – 0x0020) Result: 0x60 … >> ERROR <<174: TMS bus (#7 HIGH) 0x0040 (0x0040 – 0x0040) Result: 0x40 … >> OK <<175: TMS bus (#8 HIGH) 0x0080 (0x0080 – 0x0080) Result: 0x80 … >> OK <<
176: RST bus (All HIGH) 0x00FF (0x00FF – 0x00FF) Result: 0xFF … >> OK <<177: RST bus (All LOW) 0x0000 (0x0000 – 0x0000) Result: 0x00 … >> OK <<
178: RST bus (#1 HIGH) 0x0001 (0x0001 – 0x0001) Result: 0x01 … >> OK <<179: RST bus (#2 HIGH) 0x0002 (0x0002 – 0x0002) Result: 0x02 … >> OK <<180: RST bus (#3 HIGH) 0x0004 (0x0004 – 0x0004) Result: 0x04 … >> OK <<181: RST bus (#4 HIGH) 0x0008 (0x0008 – 0x0008) Result: 0x08 … >> OK <<182: RST bus (#5 HIGH) 0x0010 (0x0010 – 0x0010) Result: 0x10 … >> OK <<183: RST bus (#6 HIGH) 0x0020 (0x0020 – 0x0020) Result: 0x20 … >> OK <<184: RST bus (#7 HIGH) 0x0040 (0x0040 – 0x0040) Result: 0x00 … >> ERROR <<185: RST bus (#8 HIGH) 0x0080 (0x0080 – 0x0080) Result: 0x80 … >> OK <<
186: Keys buffer (All pull-up) 0x001F (0x001F – 0x001F) Result: 0x1F … >> OK <<
187: Access to LCD RAM (0xAA) 0x00AA (0x00AA – 0x00AA) Result: 0xAA … >> OK <<188: Access to LCD RAM (0x99) 0x0099 (0x0099 – 0x0099) Result: 0x99 … >> OK <<
189: Image Flash Access (get ID) 0x0002 (0x0001 – 0x0004) Result: 0x04 … >> OK <<
============== Finished =================================* Test failed!! 37 error(s).=========================================================
,
Ben Qin：
好的，我需要咨询下资深工程师，一旦有回复会立即回复您。
? ? 说：贵公司有无技术支持可以电话沟通指导
这个可以联系您的FAE。
