TI中文支持网给F28335写程序，编译过程没问题，点了Debugg之后，在Console窗口中出现如下错误，这是怎么回事？
出现这个错误前，曾用CCS3.3烧写过程序，难道是应为3.3和5.2的问题？
C28xx: Flash Programmer: Warning: The configured device (TMS320F28035), does not match the detected device (TMS320F28335). Flash Programming operations could be affected. Please consider modifying your target configuration file.
C28xx: GEL Output:Device Calibration not complete, check if device is unlocked and recalibrate.C28xx: GEL Output:Device Calibration not complete, check if device is unlocked and recalibrate.C28xx: Breakpoint Manager: Retrying with a AET breakpoint
C28xx: Trouble Setting Breakpoint with the Action "Finish Auto Run" at 0x9000: (Error -1066 @ 0x9000) Unable to set requested breakpoint in memory. Verify that the breakpoint address is in writable memory. (Emulation package 5.0.747.0)C28xx: GEL Output:Device Calibration not complete, check if device is unlocked and recalibrate.
Johnson Chen1：
楼主你好！
应该是目标配置中芯片型号选择F28035错误，应该选择为F28335芯片。
使用CCS5时，请在"target configuration"中设置好你的芯片型号和仿真器信号。
给F28335写程序，编译过程没问题，点了Debugg之后，在Console窗口中出现如下错误，这是怎么回事？
出现这个错误前，曾用CCS3.3烧写过程序，难道是应为3.3和5.2的问题？
C28xx: Flash Programmer: Warning: The configured device (TMS320F28035), does not match the detected device (TMS320F28335). Flash Programming operations could be affected. Please consider modifying your target configuration file.
C28xx: GEL Output:Device Calibration not complete, check if device is unlocked and recalibrate.C28xx: GEL Output:Device Calibration not complete, check if device is unlocked and recalibrate.C28xx: Breakpoint Manager: Retrying with a AET breakpoint
C28xx: Trouble Setting Breakpoint with the Action "Finish Auto Run" at 0x9000: (Error -1066 @ 0x9000) Unable to set requested breakpoint in memory. Verify that the breakpoint address is in writable memory. (Emulation package 5.0.747.0)C28xx: GEL Output:Device Calibration not complete, check if device is unlocked and recalibrate.
wxw wxw：
回复 Johnson Chen1:
不是这问题，我改成28335了，还是出现这种错误
给F28335写程序，编译过程没问题，点了Debugg之后，在Console窗口中出现如下错误，这是怎么回事？
出现这个错误前，曾用CCS3.3烧写过程序，难道是应为3.3和5.2的问题？
C28xx: Flash Programmer: Warning: The configured device (TMS320F28035), does not match the detected device (TMS320F28335). Flash Programming operations could be affected. Please consider modifying your target configuration file.
C28xx: GEL Output:Device Calibration not complete, check if device is unlocked and recalibrate.C28xx: GEL Output:Device Calibration not complete, check if device is unlocked and recalibrate.C28xx: Breakpoint Manager: Retrying with a AET breakpoint
C28xx: Trouble Setting Breakpoint with the Action "Finish Auto Run" at 0x9000: (Error -1066 @ 0x9000) Unable to set requested breakpoint in memory. Verify that the breakpoint address is in writable memory. (Emulation package 5.0.747.0)C28xx: GEL Output:Device Calibration not complete, check if device is unlocked and recalibrate.
Eric Ma：
回复 wxw wxw:
WXW,
如果还是出现下面的错误，那应该还是目标配置文件没有配置好，如果修改过后，是否有测试过。
C28xx: Flash Programmer: Warning: The configured device (TMS320F28035), does not match the detected device (TMS320F28335). Flash Programming operations could be affected. Please consider modifying your target configuration file.
建议使用CCSv5.新建target configuration file，然后配置为默认并launch this configuration，然后连接芯片烧写。
Eric
