uart_read 读取不到数据?-TI中文支持网

我使用CC3220SF中ti驱动uartecho例程。自己修改了sysconfig中uart驱动的Rx和Tx引脚。然后我创建了Txbuf和Rxbuf两个缓冲区，并用杜邦线把RX引脚与Tx引脚相连。以此实现自发自收的目的。

1.我使用uart_write()发送数据给Rx引脚，发现uart_read的始终不能读取到数据？

代码如下：

/*
* ======== uartecho.c ========
*/
#include <stdint.h>
#include <stddef.h>

/* Driver Header files */
#include <ti/drivers/GPIO.h>
#include "UART.h"

/* Driver configuration */
#include "ti_drivers_config.h"
#include "unistd.h"
/*
* ======== mainThread ========
*/
void *mainThread(void *arg0)
{
    UART_Handle uart;
    UART_Handle uart1;
    UART_Params uartParams;
    uint8_t TX_data[8] = {0x01,0x03,0x00,0x64,0x00,0x01,0xc5,0xd5};
    uint8_t RX_data[8] = {0};
    uint8_t count = 0;
    /* Call driver init functions */
    GPIO_init();
    UART_init();

/* Configure the LED pin */
GPIO_setConfig(CONFIG_GPIO_LED_0, GPIO_CFG_OUT_STD | GPIO_CFG_OUT_LOW);

/* Turn on user LED */
GPIO_write(CONFIG_GPIO_LED_0, CONFIG_GPIO_LED_ON);

    /* Create a UART with data processing off. */
     UART_Params_init(&uartParams);
     uartParams.readMode = UART_MODE_BLOCKING;
     uartParams.writeMode = UART_MODE_BLOCKING;
//     uartParams.writeTimeout = 1000;
     uartParams.writeDataMode = UART_DATA_BINARY;
     uartParams.readDataMode = UART_DATA_BINARY;
     uartParams.readReturnMode = UART_RETURN_FULL;
     uartParams.readTimeout = 1000;
     uartParams.baudRate = 9600;
     uartParams.dataLength = UART_LEN_8;
     uartParams.stopBits = UART_STOP_ONE;
     uartParams.parityType = UART_PAR_NONE;
     uartParams.readEcho = UART_ECHO_OFF;
    uart = UART_open(CONFIG_UART_0, &uartParams);

    if (uart == NULL) {
        /* UART_open() failed */
        while (1);
    }

    uart1 = UART_open(CONFIG_UART_1, &uartParams);
    if (uart1 == NULL) {
            /* UART_open() failed */
            while (1);
     }

    /* Loop forever echoing */
    while (1) {
        UART_write(uart1, TX_data, 8);
        count = UART_read(uart1, RX_data, 8);
        if(count > 0)
        {
            GPIO_toggle(CONFIG_GPIO_LED_0);
        }
    }
}

Kevin Qiu1：

/*!*@briefFunction that reads data from a UART with interrupt enabled.**%UART_read() reads data from a UART controller. The destination is specified*by \a buffer and the number of bytes to read is given by \a size.**In #UART_MODE_BLOCKING, %UART_read() blocks task execution until all*the data in buffer has been read.**In #UART_MODE_CALLBACK, %UART_read() does not block task execution.*Instead, a callback function specified by UART_Params::readCallback*is called when the transfer is finished.*The callback function can occur in the caller's context or in HWI or SWI*context, depending on the device-specific implementation.*An unfinished asynchronous read operation must always be canceled using*UART_readCancel() before calling UART_close().**%UART_read() is mutually exclusive to UART_readPolling(). For an opened*UART peripheral, either %UART_read() or UART_readPolling() can be used,*but not both.**@sa UART_readPolling()**@paramhandleA #UART_Handle returned by UART_open()**@parambufferA pointer to an empty buffer to which*received data should be written**@paramsizeThe number of bytes to be written into buffer**@return Returns the number of bytes that have been read from the UART,*#UART_STATUS_ERROR on an error.*/
extern int_fast32_t UART_read(UART_Handle handle, void *buffer, size_t size);

单步运行看程序是否可以执行到UART_read部分，另外看下数据是否已经发出