TI中文支持网报错内容如下：
IcePick_C: Error connecting to the target: (Error -242 @ 0x0) A router subpath could not be accessed. The board configuration file is probably incorrect. (Emulation package 8.2.0.00004)
test connection信息如下：
[Start: Texas Instruments XDS110 USB Debug Probe]
Execute the command:
%ccs_base%/common/uscif/dbgjtag -f %boarddatafile% -rv -o -S integrity
[Result]
—–[Print the board config pathname(s)]————————————
C:\Users\rene\AppData\Local\TEXASI~1\CCS\
CCS910\1\0\BrdDat\testBoard.dat
—–[Print the reset-command software log-file]—————————–
This utility has selected a 100- or 510-class product.
This utility will load the adapter 'jioxds110.dll'.
The library build date was 'Jun 3 2019'.
The library build time was '15:24:38'.
The library package version is '8.2.0.00004'.
The library component version is '35.35.0.0'.
The controller does not use a programmable FPGA.
The controller has a version number of '5' (0x00000005).
The controller has an insertion length of '0' (0x00000000).
This utility will attempt to reset the controller.
This utility has successfully reset the controller.
—–[Print the reset-command hardware log-file]—————————–
The scan-path will be reset by toggling the JTAG TRST signal.
The controller is the XDS110 with USB interface.
The link from controller to target is direct (without cable).
The software is configured for XDS110 features.
The controller cannot monitor the value on the EMU[0] pin.
The controller cannot monitor the value on the EMU[1] pin.
The controller cannot control the timing on output pins.
The controller cannot control the timing on input pins.
The scan-path link-delay has been set to exactly '0' (0x0000).
An error occurred while hard opening the controller.
—–[An error has occurred and this utility has aborted]——————–
This error is generated by TI's USCIF driver or utilities.
The value is '-242' (0xffffff0e).
The title is 'SC_ERR_ROUTER_ACCESS_SUBPATH'.
The explanation is:
A router subpath could not be accessed.
The board configuration file is probably incorrect.
[End: Texas Instruments XDS110 USB Debug Probe]
Viki Shi：
请问你使用的开发板或芯片是什么？
user6340973：
回复 Viki Shi:
开发板是CC1310 LaunchPad，CC1310F128
user6340973：
回复 Viki Shi:
MSP432 E401YT REV B
Viki Shi：
回复 user6340973:
第一次使用就出现这个报错吗？还是做了什么操作？
user6340973：
回复 Viki Shi:
我是在网上买了一个XDS110的仿真器，然后连接好TMS,TCK,RESET,3.3V及GND引脚进行下载程序时遇到的这个情况
user6340973：
回复 Viki Shi:
自己买的XDS110，连接了TCK,TMS,RESET,3.3V及GND后，下载程序时出现了这个情况
Viki Shi：
回复 user6340973:
为什么另买一个XDS110？CC1310 LaunchPad板上自带一个debugger，是否能正常使用？
user6340973：
回复 Viki Shi:
项目需要，要引出这些管脚，自带的是可以用的
Viki Shi：
回复 user6340973:
用外接的debugger，我建议你买根线，直接按下图这样连：
by default. If you want to debug the CC1310 from an external debugger, you need to remove all the jumpers and connect the debugger to the socket marked CC1310 In.
user6340973：
回复 Viki Shi:
图片没有显示
