TI中文支持网你好技术老师：
现在有一个项目需要用到贵公司的ths8200，输入是1080P 60 Hz 30bit RGB 444，输出Ypbpr。现在调试上遇到一些问题，发现输出画面亮度有点亮，用K-8258信号发生器产生color-56 50%到100%亮度单色画面，红色和蓝色不同亮度下区分不明显，输入32灰阶发现低3灰阶和高3灰阶都饱和，颜色稍微有点偏红。使用了CSC转换，寄存器设置如下，还有请教一下CSM寄存器是不是可以调节输出色彩的，如何配置？忘回复，非常感谢。
printf("\r\n ### 1080P ### \r\n");
THS8200_WriteByte(0x03,0x81); // chip_ctl // CSC
THS8200_WriteByte(0x04,0x00);
THS8200_WriteByte(0x05,0xDA);
THS8200_WriteByte(0x06,0x80);
THS8200_WriteByte(0x07,0x78);
THS8200_WriteByte(0x08,0x02); THS8200_WriteByte(0x09,0x0C);
THS8200_WriteByte(0x0A,0x02);
THS8200_WriteByte(0x0B,0xDC);
THS8200_WriteByte(0x0C,0x81);
THS8200_WriteByte(0x0D,0x84);
THS8200_WriteByte(0x0E,0x81); THS8200_WriteByte(0x0F,0xDC);
THS8200_WriteByte(0x10,0x00);
THS8200_WriteByte(0x11,0x4A);
THS8200_WriteByte(0x12,0x02);
THS8200_WriteByte(0x13,0x0C);
THS8200_WriteByte(0x14,0x80); THS8200_WriteByte(0x15,0x30);
THS8200_WriteByte(0x16,0x00);
THS8200_WriteByte(0x17,0x08);
THS8200_WriteByte(0x18,0x01);//0x02);//cscoffset=0x79
THS8200_WriteByte(0x19,0xE5);//0x01);
THS8200_WriteByte(0x1C,0x20); // composite sync amplitude control THS8200_WriteByte(0x1D,0xFF); THS8200_WriteByte(0x1E,0x49); THS8200_WriteByte(0x1F,0xB6); THS8200_WriteByte(0x20,0xFF); THS8200_WriteByte(0x21,0xFF); THS8200_WriteByte(0x22,0xFF); THS8200_WriteByte(0x23,0x13); THS8200_WriteByte(0x24,0x15); // horizontal timing setup
THS8200_WriteByte(0x25,0x2C); THS8200_WriteByte(0x26,0x58); THS8200_WriteByte(0x27,0x2C);
THS8200_WriteByte(0x28,0x84);
THS8200_WriteByte(0x29,0x00); THS8200_WriteByte(0x2A,0xC0); THS8200_WriteByte(0x2B,0x00); THS8200_WriteByte(0x2C,0x00); THS8200_WriteByte(0x2D,0x00); THS8200_WriteByte(0x2E,0x00); THS8200_WriteByte(0x2F,0x58); THS8200_WriteByte(0x30,0x00); THS8200_WriteByte(0x31,0x00); THS8200_WriteByte(0x32,0x58); THS8200_WriteByte(0x33,0x00); THS8200_WriteByte(0x34,0x08);
THS8200_WriteByte(0x35,0x98); THS8200_WriteByte(0x36,0x80); THS8200_WriteByte(0x37,0x02);
THS8200_WriteByte(0x38,0x80); THS8200_WriteByte(0x39,0x44); THS8200_WriteByte(0x3A,0x65);
THS8200_WriteByte(0x3B,0x65);
// CSM setup not required if not used
THS8200_WriteByte(0x4F,0x00);
//discrete output sync control THS8200_WriteByte(0x70,0x18); THS8200_WriteByte(0x71,0x48); THS8200_WriteByte(0x72,0x44); THS8200_WriteByte(0x73,0x17); THS8200_WriteByte(0x74,0x04); THS8200_WriteByte(0x75,0x65); THS8200_WriteByte(0x76,0x00);
THS8200_WriteByte(0x77,0x02);
THS8200_WriteByte(0x78,0x32);
// discrete input sync control – use to align picture
THS8200_WriteByte(0x79,0x08);//THS8200_WriteByte(0x79,0x00);
THS8200_WriteByte(0x7A,0x17);//0x00);//h
THS8200_WriteByte(0x7B,0x00); THS8200_WriteByte(0x7C,0x04);//0x01); //v
THS8200_WriteByte(0x82,0x1B);
MichaelSheep：
您好，抱歉回复较慢，
您的问题我建议您在以下链接想关的板块来发帖，这个板块有视频方面的专家。希望能帮到您！
http://www.deyisupport.com/question_answer/dsp_arm/f/22/t/31240.aspx
Eason Wang：
您好，
亮度的问题，通常可以用调节FSADJ1/2外接的电阻大小来进行调节的。
确认一下，你的这台测试设备，是作为源来使用吧？是不是要通过视频decoder先到某主芯片，再去驱动THS8200的？这里的话可能需要排除一下前端的影响，或者你也可以直接在主芯片端发送测试图样。
你所说的灰阶饱和，指的是这几个灰阶无法辨认？ 这个和显示器也有一定关系的。 你可以再确认一下，是否黑足够黑，白足够白？
色偏的问题，你可以直接测量RGB的数字信号值来确认问题是在哪一端产生的。
如果在THS8200上做调节，你看看csc_offset这几个寄存器，对色彩有一定的影响。
CSM是拿来调整输出范围的，是可以改变颜色，但是结果显得不可控了。 我的建议是，尽量保留原配的设置，因为这个是在最多的硬件上验证可用的配置，仍然是最可信的。 多看看硬件和信号测量上得到的直接证据，不然直接去改寄存器可能会改好了这个改坏了那个。。。
